Moving a plant to fully synthetic gear oil: the risks to weigh
Summary
Switch the whole plant to synthetic gear oil only when the seal, paint, residual-oil and payback checks all pass; if any check fails, switch gearbox by gearbox. The risks to weigh are seal shrinkage, paint attack by polyglycol oils, sludge from mixed oils, a lost OEM warranty and a payback that rests on untested assumptions.
SEW-EURODRIVE states that synthetic oils must not be mixed with mineral oils, and that a switch from mineral to synthetic oil needs a thorough flush with the new oil grade (SEW-EURODRIVE, 2026).
SEW-EURODRIVE approves NBR radial oil seals for oil sump temperatures of -40 to +80 °C and FKM seals for -25 to +115 °C (SEW-EURODRIVE, 2021).
One polyglycol (PAG) gear oil data sheet warns that seals previously exposed to mineral oil may shrink in the PAG oil, so replacing them may be advantageous (Motul, 2025).
In a worm gear with 315 mm center distance tested on FZG equipment, an ISO VG 460 polyglycol oil measured about 3% higher efficiency than mineral oil in tests by Mautner et al., as reported by Skulić et al. (Skulić et al., 2017).
This answer covers enclosed industrial gearboxes that run on mineral gear oil and would move to a PAO, polyglycol or ester synthetic gear oil. It does not cover automotive gear oils, food-grade (H1) changeovers driven by hygiene rules, or wind turbine gearboxes, which follow the turbine maker's own conversion procedure.
Which gearboxes should switch to synthetic gear oil first, and which should wait?
The gearboxes to switch first are those where synthetic oil fixes a measured problem: high sump temperature, short oil life, or high losses in worm gear sets. Gearboxes that run cool, have no oil-related failures and whose OEM lubricant list leaves out your chosen synthetic type should wait.
Build the list from the records you already keep on each gearbox: maker and series, seal material, sump temperature, last inspection notes and oil analysis history. A gearbox without records goes into a later phase until you have those facts.
Use the table to decide, for each gearbox, whether the switch goes now, later or not at all.
Gearbox condition | Plant-wide switch | Phased switch or keep current oil | Why |
|---|---|---|---|
OEM list approves the synthetic type and seal material | Yes, if payback holds | No need to phase | Warranty voids with unapproved oil (SEW-EURODRIVE, 2021) |
NBR seals and sump above +80 °C | No | Phase with seal change to FKM | NBR approved to +80 °C, FKM to +115 °C (SEW-EURODRIVE, 2021) |
Polyglycol planned, interior paint unknown | No | Phase after paint check | PAG not compatible with oil-based paints (Phillips 66, 2026) |
Varnish or sludge found at last inspection | No | Clean and flush first | One ester gear oil's solvency can shorten deep filter life (Davor for FUCHS PLANTOGEAR S, 2026) |
No measured problem and no OEM approval | No | Keep current oil | Payback depends on a problem the switch removes |
The second row is easy to miss. A hot-running gearbox with NBR seals cannot move to synthetic oil until the seals are changed, so it belongs in a later phase. Rank the remaining gearboxes by the size of the problem you measured on each one.
How do seals and internal paint react when you switch to synthetic gear oil?
Seals and internal paint react according to the synthetic oil's base oil. Polyalphaolefin (PAO) can shrink some seals, and esters can swell them. Polyglycol (PAG) can shrink seals that were exposed to mineral oil and can attack some paints. Check both before the switch, not after a leak.
On seals, OELCHECK notes that "some seals shrink when in contact with PAO and PIB, ester oil causes them to swell" (OELCHECK, 2026); PIB is polyisobutene. A PAG gear oil data sheet states that seals previously exposed to mineral oil may shrink in the PAG oil, so replacing them may be advantageous (Motul, 2025). Sump temperature sets a second limit: SEW-EURODRIVE approves NBR oil seals up to +80 °C and FKM up to +115 °C oil sump temperature (SEW-EURODRIVE, 2021).
On paint, one PAG gear oil maker lists compatibility with epoxy paints and states it is not compatible with oil-based paints (Phillips 66, 2026). An ester gear oil supplier states that paints not compatible with esters are not recommended and that two-component coatings can generally be used (Davor for FUCHS PLANTOGEAR S, 2026).
If you do not know the paint or seal material, ask the gearbox OEM or have a sample tested. ASTM D471-16a(2021) is the active test method for the effect of liquids on rubber, and a laboratory can run it on your seal compound in the new oil.
How much old mineral oil can stay in a gearbox after a switch to synthetic gear oil?
How much mineral oil may stay depends on the new base oil. PAO mixes with mineral oil, while polyglycol oils should not be mixed with it at all. No single residual limit applies to all synthetic types.
PAO and polyisobutene base oils "are similar to mineral oil and therefore also mix well with mineral oil-based lubricants" (OELCHECK, 2026). Polyglycol is different: one PAG gear oil data sheet says the oil must not be mixed with mineral or PAO based oils (Motul, 2025), and another maker states its PAG oil is not compatible with petroleum oils (Phillips 66, 2026).
The gearbox maker's own rule can be stricter than either: for its X..e gear units, SEW-EURODRIVE does not permit mixing synthetic oils with mineral oils or with other synthetic oils (SEW-EURODRIVE, 2026).
For ester gear oils, one supplier recommends reducing residual mineral oil to approximately lower than 2%, referring to the ISO 15380 changeover guideline, table A1 (Davor for FUCHS PLANTOGEAR S, 2026). ISO 15380, now in its 2023 edition, specifies requirements for environmentally acceptable hydraulic fluids in categories HETG, HEPG, HEES and HEPR (ISO, 2023). Treat that 2% as a supplier's target for that ester product, not a gear oil standard.
The PAG data sheet also warns that contamination with significant quantities of other lubricants can lead to sludging and foaming (Motul, 2025). Sample the new charge after the first days of running to confirm.
How do you flush a gearbox before filling it with synthetic gear oil?
To flush a gearbox before a synthetic fill, drain the old oil warm, flush with a small charge of the new oil, drain again and refill, as gear unit makers ask (SEW-EURODRIVE, 2026).
Read the SDS (safety data sheet) of the old oil, the new oil and any flushing oil. Follow its handling and disposal sections, and your site's used-oil disposal rules for the drained oil.
Run the gearbox until the oil is warm, then drain it as fully as possible, including lines and pockets where oil is trapped (Motul, 2025); one gear unit maker says to avoid oil temperatures above 50 °C when draining (SEW-EURODRIVE, 2026).
Remove residual sludge and, if the design allows, inspect for deposits.
Flush with the minimum quantity of the new oil, running under no load, then drain while warm; repeat if necessary (Motul, 2025).
Inspect seals and replace deteriorated ones before the final fill (Motul, 2025).
Fill with the new oil, and replace or check the filters.
Inspect the oil after one or two days in use for foreign material (Motul, 2025).
For wind turbine gearboxes, one oil maker gives its own steps: drain at an oil temperature not less than 30 °C, and circulate the flushing oil to at least 60 °C for at least one hour (ExxonMobil, 2026). Use those values only for wind turbines.
One ester gear oil supplier warns its oil's solvency can shorten deep filter life and says to check or replace filters one week after the changeover (Davor for FUCHS PLANTOGEAR S, 2026).
Does a synthetic gear oil switch affect the gearbox warranty?
A switch affects the gearbox warranty when the new oil, or the temperature range it runs at, is not on the gearbox maker's approved list. SEW-EURODRIVE states the rule plainly for its gear unit series.
"If other lubricants are used in the gear units and/or lubricants are used with other temperature ranges than the ones recommended, the right to claim under warranty will become invalid" (SEW-EURODRIVE, 2021). The same approval document limits which radial oil seal materials may be used with each lubricant, so an approval covers oil and seal together. It also flags that helical-worm gear units using polyglycol oil need a direct check with the maker (SEW-EURODRIVE, 2021).
Before a plant-wide switch, list each gearbox by maker, series and serial number, and find the maker's current lubricant table for each one. Lubricant tables change; SEW-EURODRIVE notes that a printed table is valid at printing and points to its website for the latest version (SEW-EURODRIVE, 2026).
Meeting the industry gear oil specification does not replace that check. An oil that meets ANSI/AGMA 9005-F16, the edition that superseded ANSI/AGMA 9005-E02 in 2016 (STLE, 2024), still needs the gearbox maker's own approval. Run the check on gearboxes out of warranty too: the approved list also tells you which seal materials the maker tested.
Which payback assumptions must hold before a plant-wide synthetic gear oil switch?
Four payback assumptions must hold before a plant-wide switch: a longer drain interval, a measurable efficiency gain on your gear type, a lower sump temperature, and switching costs that include flushing, seals and downtime. If any one fails, compare the switch with keeping the current oil.
Drain interval: makers state longer oil life for synthetic oils, and one PAG data sheet gives an anticipated service lifetime substantially in excess of 10,000 hours at 100 °C (Motul, 2025). Your interval is set by oil analysis on your own gearboxes, not by the data sheet.
Efficiency: the gain depends on gear type. On a 315 mm center-distance worm gear, ISO VG 460 polyglycol measured about 3% higher efficiency than mineral oil in tests by Mautner et al., as reported by Skulić et al. (Skulić et al., 2017). Worm gears slide heavily, so do not assume a helical gearbox gains the same.
Costs: count flushing oil, seal kits, labor, downtime and the risk of a failed changeover. A feasibility review case in Lubinpla fixes these options and assumptions, then compares them under base, upside, downside and stress scenarios, with keeping the current oil as one of the options. Before you approve any switch, see how to weigh the risks of moving a customer to a new formulation, which applies the same option-by-option logic.
Synthetic gear oil switch mistakes plants make
Plants go wrong by switching every gearbox at once, skipping the flush, ignoring seal and paint checks, and judging payback from a data sheet instead of their own oil analysis. Each of these turns a switch that pays into a source of leaks or downtime.
Switching all gearboxes in one shutdown: any fault in the procedure then repeats across the plant.
Topping up a synthetic gearbox with mineral oil from the store: SEW-EURODRIVE forbids mixing synthetic and mineral oils (SEW-EURODRIVE, 2021). Label each gearbox and its top-up containers.
Draining cold: oil stays in pockets and lines and becomes the residual you then have to dilute.
Skipping the filter check: one ester gear oil supplier warns its oil's solvency can shorten deep filter life after the change (Davor for FUCHS PLANTOGEAR S, 2026).
Reusing NBR seals in gearboxes that run above their approved +80 °C sump temperature (SEW-EURODRIVE, 2021).
Filling polyglycol into a gearbox with oil-based interior paint (Phillips 66, 2026).
Reading the efficiency gain from a worm gear test as the gain a helical gearbox will see.
Start with a pilot group of two or three gearboxes from one series, sample their oil, and widen the switch only when the pilot passes.
Frequently asked questions
Can you top up a PAO synthetic gear oil with mineral gear oil?
Only in an emergency, and only if the gearbox maker allows it. PAO does mix physically with mineral oil (OELCHECK, 2026), but SEW-EURODRIVE does not permit mixing synthetic and mineral oils in its X..e gear units (SEW-EURODRIVE, 2026). If you have topped up, change the oil at the next stop.
Do you need new seals when you switch to synthetic gear oil?
Not always. Replace seals that are worn. Before a polyglycol fill, consider replacing seals that were exposed to mineral oil, because they may shrink (Motul, 2025). In every case, check the seal material against the gearbox maker's approved temperature range.
Is synthetic gear oil worth it in a gearbox that runs cool?
Often not on payback alone. Synthetic oils pay through longer oil life and lower losses, and those matter most in hot or heavily sliding gear sets such as worm gears. A cool helical gearbox that already gets long oil life gives little to recover, so keeping the current oil can be the better option.