How to write a cleaning procedure SOP for a parts-cleaning line
Summary
A parts-cleaning SOP takes 7 steps to write: scope, chemistry and concentration, temperature and time, mechanical action, rinse and dry, cleanliness check, bath management. The steps fit immersion, spray and ultrasonic lines that clean metal parts before assembly, coating or shipping, with the cleaner maker's technical data sheet and safety data sheet as the source of every setting.
Aqueous parts-cleaning results depend on four linked variables, time, agitation, concentration and temperature, and raising any one can raise cleaning efficiency (Master Fluid Solutions, 2019).
In a used cleaning bath, about 1% oil can shift a refractometer reading by about 1 Brix degree, so titration is the recommended concentration check (Master Fluid Solutions, 2019).
The ASTM F22-21 water-break test can detect molecular layers of hydrophobic contaminants but is not quantitative and suits go or no-go checks (ASTM International, 2021).
Where liquids that may harm skin are used in a dip tank, US OSHA requires an emergency shower and eye-wash station close to the operation, or a quick-opening water hose that meets the rule in its place (US OSHA, 29 CFR 1910.124(g)(2), eCFR 2026).
This procedure covers routine cleaning of new or in-process metal parts on a production line. It does not cover vapor degreasing with halogenated solvents, cleaning of equipment already in service, or the passivation of stainless steel; each of those has its own standards and permits.
What do you need before writing a parts-cleaning SOP?
Before writing a parts-cleaning SOP you need five inputs: the cleaner's technical data sheet, its safety data sheet, the cleanliness the next process requires, the washer's design limits and the part materials. The technical data sheet gives the product's concentration range, its temperature range and its titration method, the supplier's test for bath concentration. The safety data sheet lists the hazards, the personal protective equipment and the first aid, and the SOP repeats each one at the step where it applies.
The next process sets the target. Parts headed for painting, plating or adhesive bonding need a surface free of oil films, while parts headed for assembly may be judged mainly on particles and chips. Write the target as a check with a pass value, not as "clean".
Then collect the washer's limits: tank volume, maximum temperature, spray pressure or ultrasonic power, filtration and oil skimming. List every part material too, because one cleaner may suit steel and stain aluminum or brass.
Keep the safety data sheet with the SOP. US OSHA requires employers to keep safety data sheets readily accessible to employees during each work shift (US OSHA, 29 CFR 1910.1200(g)(8), eCFR 2026), and in the EU the supplier must provide one no later than first supply (Regulation (EC) No 1907/2006, Article 31(8), 2026). Because the SOP goes to the customer, internal notes stay out of it; the same judgment applies as in deciding what to leave out of a technical report for a customer.
How do you write the parts-cleaning procedure step by step?
You write the parts-cleaning procedure as seven numbered steps. Each step holds one action and one value, taken from the cleaner's technical data sheet or the customer's requirement. Example values are illustrative.
Scope. Name the parts, materials, soils and the washer.
Chemistry and concentration. Name the cleaner and the target range, for example 3 to 5% by titration (illustrative), with the titration method and factor the supplier specifies for that product (Master Fluid Solutions, 2019). Wear the eye and skin protection listed in safety data sheet section 8; US OSHA requires appropriate eye or face protection against liquid chemicals and caustic liquids (US OSHA, 29 CFR 1910.133(a)(1), eCFR 2026).
Temperature and time. Set the bath range and the minimum cycle time within the washer's maximum, for example 55 to 65 °C for 4 minutes (illustrative).
Mechanical action. State the spray pressure, the agitation or ultrasonic setting, and the part orientation in the basket.
Rinse and dry. Give the rinse type and its limit, then the drying method and the time by which parts must be dry.
Cleanliness check. Name the check, the sample size and the pass value from the table in the next section.
Bath management. Give the titration frequency, the top-up rule and the replacement trigger.
Cleaners whose safety data sheet classifies them as corrosive to skin or eyes, often heated alkaline cleaners, need the emergency equipment added to step 2. US OSHA requires facilities for quick drenching or flushing of the eyes and body where the eyes or body of any person may be exposed to injurious corrosive materials (US OSHA, 29 CFR 1910.151(c), eCFR 2026). On a dip tank with liquids that may harm skin, it also requires an emergency shower and eye-wash station close to the operation, or the hose it allows in their place (US OSHA, 29 CFR 1910.124(g)(2), eCFR 2026).
How do you check that parts are clean after the cleaning procedure?
You check parts after the cleaning procedure with the test the next process depends on: a water-break or wipe test for oil films, a particle extraction for assembly cleanliness, and a visual check for residue and flash rust. In a water-break test, a clean part holds a continuous film of water, while on an oily surface the water beads or breaks. ASTM A380/A380M-25, a practice written for stainless steel parts, lists visual inspection, wipe tests, residual pattern and the water-break test among its bases for cleanness acceptability, and notes that visual inspection may not reveal thin films of oil (ASTM International, 2025).
The table tells the line when to accept parts, when to re-clean them and when to adjust concentration or temperature.
Check | Pass | Fail and what to do |
|---|---|---|
Water-break (ASTM F22-21) | Continuous water film, no breaks (ASTM International, 2021) | Water beads or breaks: titrate the bath, check temperature, re-clean one batch and retest |
White wipe on a cleaned part | No visible soil on the cloth | Soil on the cloth: check spray nozzles or agitation, then cycle time |
Visual, after drying | No residue, staining or rust | White residue: check rinse and concentration; rust: shorten time to dry, check inhibitor in the cleaner |
Particles (ISO 16232:2018 method) | Below the customer's limit (ISO, 2018) | Above the limit: check filtration and part orientation, then re-clean |
The water-break row matters most. ASTM F22-21 describes it as "not quantitative" and "typically restricted to applications where a go/no go evaluation of cleanliness will suffice" (ASTM International, 2021). It gives a pass or a fail rather than a number, so a failed water-break sends the batch back, and the fix starts with a titration.
ISO 16232:2018 sets methods only; it "does not define any cleanliness limit values", so the particle limit must come from the customer (ISO, 2018).
When should the cleaning bath be topped up or replaced?
Top up the cleaning bath when titration shows concentration below the SOP's lower limit. Replace it when it no longer cleans parts to the pass value even though concentration and temperature are in range.
Concentration drifts in both directions. Too low a concentration often brings parts that do not come clean, corrosion on parts or washer, and odor; too high a concentration brings residue, staining, excess product use, sludge and dermatitis (Master Fluid Solutions, 2019). Check concentration by titration, with the product's own method. Master Fluid Solutions advises that a refractometer reading works only on a fresh charge, a newly made bath, because about 1% oil changes it by about 1 Brix degree (Master Fluid Solutions, 2019).
Do not schedule bath changes by the calendar in the SOP. Pinellas County's guidance for parts washers says to change the solution only when it no longer cleans adequately, and not to change an aqueous solution just because it looks dirty, since many turn brown or gray without losing cleaning ability (Pinellas County Solid Waste, accessed 2026).
When the bath is replaced, the SOP should send the spent solution, sludge and filters to an accurate waste determination before disposal under the local hazardous waste rules, as the same guidance advises. It should also point to safety data sheet section 13 for disposal. If a worker must enter the tank to clean it, US OSHA applies its permit-required confined space rules as applicable (US OSHA, 29 CFR 1910.124(e), eCFR 2026).
Common mistakes in parts-cleaning procedures
The most common mistakes in parts-cleaning procedures are settings without numbers, a concentration check that does not fit the bath, and a cleanliness check that cannot see the soil that matters. Each one lets a line drift out of control with nobody noticing.
Writing "clean thoroughly" or "keep the bath hot" gives the operator nothing to measure. Every step needs a range and a unit, and the range must come from the technical data sheet or a trial, not from habit.
The second mistake is checking a used bath with a refractometer. Dissolved oil raises the reading, so the bath looks stronger than it is (Master Fluid Solutions, 2019). A titration kit run with another product's factor gives a wrong number with false confidence; Master Fluid Solutions calls it "critically important" to use the method and factors specified for the product in use (Master Fluid Solutions, 2019).
The third is relying on a visual check alone before painting or bonding: a part can look clean and still carry an oil film that a water-break test would show. The last is leaving the rinse step out of the SOP when cleaner residue will interfere with the next process. That gap shows up later, as staining or poor coating adhesion, rather than at the washer.
When should you call a cleaning chemistry specialist about a parts-cleaning SOP?
Call a cleaning chemistry specialist about a parts-cleaning SOP in three cases: the line fails its cleanliness check with concentration, temperature and time all in range; a new part material or soil enters the line; or the next process changes its cleanliness requirement. In each case the SOP's settings no longer match the job, and adjusting them by trial on production parts risks scrap.
Bring the specialist the SOP, the titration log, the failed check results and the safety data sheet. With those, a specialist can tell whether the cleaner chemistry still fits, whether the line needs a different rinse or an inhibitor, and which check the customer's next process really requires. Before any change to temperature or concentration outside the technical data sheet range and the safety data sheet range, call the cleaner supplier as well.
Once the settings are agreed, Lubinpla's document writing can produce the SOP as a user-guide document that holds only the conditions settled in the conversation and, after the user approves it, register it to the customer as a PDF.
Frequently asked questions
Does the water-break test work on every part?
No. ASTM F22-21 notes that on very rough or porous surfaces the sensitivity of the water-break test may be significantly decreased, and that for surfaces that cannot be immersed or doused, Test Method F21 may be better suited (ASTM International, 2021). For such parts, name the alternative check in the SOP.
Can conductivity replace titration for bath concentration?
Conductivity can measure concentration and is useful for automating cleaner makeup in the washer, according to Master Fluid Solutions, but the same bulletin recommends titration in nearly all situations (Master Fluid Solutions, 2019). Use conductivity for control, and confirm it by titration at the frequency the SOP sets.
Who keeps the safety data sheet for the cleaner?
In the US, the employer keeps copies of the safety data sheet for each hazardous chemical in the workplace and makes them readily accessible during each work shift (US OSHA, 29 CFR 1910.1200(g)(8), eCFR 2026). In the EU, the supplier provides it free of charge no later than first supply (Regulation (EC) No 1907/2006, Article 31(8), 2026).
Do OSHA dip tank rules cover a parts-cleaning tank?
US OSHA's dipping and coating rules apply when a dip tank holds a liquid other than water and the liquid or its vapor is used to clean an object; cleaning and degreasing are listed examples (US OSHA, 29 CFR 1910.123, eCFR 2026). Check each tank's coverage against the rule text.