How to replace 2-butoxyethanol in an industrial cleaner
Summary
Replacing 2-butoxyethanol in an industrial cleaner takes 5 steps: name its job, shortlist glycol ethers, check flash point and exposure limits, rebalance, retest. The method applies to water-based cleaners, where 2-butoxyethanol keeps oils dissolved in water. Candidates rarely match all three of its jobs at once, so plan on a rebalance and full retest, not a one-for-one swap.
Industrial and household window cleaning agents have contained 2-butoxyethanol at 1% to 30% by volume (Vincent et al. 1993, cited by ATSDR, 1998).
The US OSHA PEL for 2-butoxyethanol is 50 ppm as an 8-hour TWA, while the NIOSH REL is 5 ppm (OSHA Annotated Table Z-1, NIOSH values as of 2021).
The EU occupational exposure limit is 20 ppm as an 8-hour TWA and 50 ppm short term, with a skin notation (ICSC 0059, 2024).
Australia's 1996 assessment recommended considering substitution where workers face prolonged skin contact with products at 30% 2-butoxyethanol or more (NICNAS, 1996).
This guide covers water-based industrial cleaners and degreasers that use 2-butoxyethanol as a coupler or cosolvent. It does not cover coatings, inks or solvent-only degreasers, and it does not decide label classification for your product, which comes from your supplier SDS and a test on the final blend.
What do you need before replacing 2-butoxyethanol in a cleaner?
Before replacing 2-butoxyethanol in a cleaner, you need the current formula with percentages, the safety data sheet (SDS) for every ingredient, the original product's test results and a clear reason for the change. The reason sets the target. If exposure limits drive the change, the candidate needs a higher limit or none set. If flammability drives it, the candidate needs a higher flash point.
Gather these items:
The formula sheet, with surfactants, builders, pH and the 2-butoxyethanol level.
The SDS for 2-butoxyethanol and for each candidate glycol ether. Read the flash point, exposure limit and handling sections before any lab work.
Retained samples of the current cleaner, so you can compare the new blend side by side on the same soils and substrates.
The original results for phase stability, cleaning, drying and residue. If you have none, run them on the current product first.
Your target markets, because limits differ by jurisdiction.
Australia's priority assessment of 2-butoxyethanol in cleaning products states that substitutes "need to be thoroughly tested and, in general, they should demonstrate a lower toxicity, irritancy and potential for skin absorption in humans" (NICNAS, 1996). That sets the bar a replacement has to clear, and cleaning performance is only part of it.
How do you replace 2-butoxyethanol in an industrial cleaner, step by step?
Replacing 2-butoxyethanol in an industrial cleaner follows 5 steps, and each one ends with a decision you record before moving on. Work at bench scale in small batches. Keep every solvent SDS at hand, remove ignition sources, and store and handle the neat (undiluted) solvents under US OSHA 29 CFR 1910.106 or your jurisdiction's flammable liquids rule.
Name the job. Record which of the three jobs this formula needs from the solvent: coupling oils and surfactants into water, dissolving soil, or controlling how fast the film dries.
Shortlist candidates. Pick two or three glycol ethers that cover the main job. Judge coupling by water solubility and drying by vapour pressure (see the candidate table).
Check flash point and exposure limits. Read each candidate SDS for the closed-cup flash point and every limit that applies in your markets. Drop any candidate that moves the product into a stricter flammability category.
Rebalance. Start at equal weight, then adjust the candidate level, a hydrotrope or the surfactant package until the blend is clear and stable.
Retest. Run the full check table from the retest section on the final blend, including a measured flash point, then update the SDS and label.
Step 4 is where most trials fail: a candidate that cleans well can still split the product in storage. For the wider method of swapping any raw material in an existing formula, see how to substitute a raw material in an existing formulation.
What does 2-butoxyethanol do in an industrial cleaner?
2-Butoxyethanol does three jobs in an industrial cleaner. It couples oily and watery ingredients, holding them together in one clear phase; it dissolves greasy soil; and it evaporates at a rate that suits wipe-on cleaners. ATSDR describes the coupling job directly: "Functioning as a coupling agent, the compound stabilizes immiscible ingredients in metal cleaning products, textile lubricants, hydraulic fluids, cutting oils, and liquid household cleaning products" (ATSDR, 1998).
Those same jobs make the molecule hard to replace. ATSDR credits its usefulness to a "well-balanced distribution of hydrophilic and hydrophobic groups, complete miscibility with water at room temperature, and an appropriate rate of evaporation" (ATSDR, 1998). Few candidates have all three.
Concentrations vary widely. ATSDR reports that window cleaning agents have contained 1% to 30% by volume, and that household products in 1977 averaged 2.8% (ATSDR, 1998). A cleaner at the low end usually needs only the coupling job, so a partly water-soluble candidate plus a hydrotrope may work. A cleaner near the high end also depends on solvency, so the candidate must dissolve the soil as well as stay in solution.
To find which job matters, run the current product without the 2-butoxyethanol. Whatever fails first, clarity, soil removal or drying, is the job the replacement must cover.
Which glycol ethers can replace 2-butoxyethanol in a cleaner?
The glycol ethers most often screened to replace 2-butoxyethanol in a cleaner are propylene glycol ethers. Choose by the job they must cover: water solubility for coupling, vapour pressure for drying and flash point for safety. Australia's assessment notes that glycol ethers include both ethylene and propylene glycol monoalkyl ethers, and that as a group they are "miscible with water and most organic solvents" (NICNAS, 1996). Individual members differ, as the table shows.
The table below shows which candidate to try first for each job. Values come from each substance's chemical safety card or database record, at the temperatures shown. Confirm the closed-cup value on your supplier SDS, because the cards do not all state the method.
Candidate | Water solubility | Flash point | Vapour pressure |
|---|---|---|---|
2-Butoxyethanol (reference) | Miscible (ICSC 0059, 2024) | 60 °C (ICSC 0059, 2024) | 0.10 kPa at 20 °C (ICSC 0059, 2024) |
Propylene glycol n-butyl ether (PnB) | 6 g/100 mL, moderate (ICSC 1614, 2005) | 63 °C (ICSC 1614, 2005) | 0.187 kPa at 25 °C (ICSC 1614, 2005) |
Propylene glycol n-propyl ether (PnP) | Miscible (HSDB, via PubChem) | 48 °C (HSDB, via PubChem) | Not checked for this article |
Dipropylene glycol methyl ether (DPM) | Very good (ICSC 0884, 1999) | 74 °C (ICSC 0884, 1999) | 53.3 Pa at 26 °C (ICSC 0884, 1999) |
Propylene glycol methyl ether (PM) | Very good (ICSC 0551, 1997) | 38 °C (ICSC 0551, 1997) | 1.2 kPa at 20 °C (ICSC 0551, 1997) |
Read the PnB row first. Its 63 °C flash point sits close to that of 2-butoxyethanol, but its water solubility of 6 g/100 mL (ICSC 1614, 2005) means PnB will not couple a concentrate on its own. Pair it with a fully miscible candidate or a hydrotrope. DPM has the highest flash point and the lowest vapour pressure in the table, so it suits a blend that must stay wet longer on the surface.
How do flash point and exposure limits change when you replace 2-butoxyethanol?
Flash point and exposure limits both change when you replace 2-butoxyethanol, and either one can change the product's label while cleaning performance stays the same. Under the US Hazard Communication Standard, a flammable liquid is Category 3 at a flash point from 23 °C to 60 °C and Category 4 above 60 °C up to 93 °C (OSHA, 29 CFR 1910.1200 Appendix B).
2-Butoxyethanol sits right on that line. The ILO-WHO card gives 60 °C closed cup and the hazard statement "Flammable liquid and vapour" (ICSC 0059, 2024), while Australia's assessment cites 62 °C from NIOSH (NICNAS, 1996). As neat solvents, PM at 38 °C and PnP at 48 °C are clearly Category 3, while PnB at 63 °C (ICSC 1614, 2005) and DPM at 74 °C (ICSC 0884, 1999) are above the line. Water and the other ingredients change the flash point of the finished blend, so measure the blend itself rather than assume.
Exposure limits move the other way. DPM has a US OSHA permissible exposure limit (PEL) of 100 ppm (OSHA Annotated Table Z-1) and an EU limit of 50 ppm (ICSC 0884, 1999). PM has an EU limit of 100 ppm (ICSC 0551, 1997). The PnB card lists no occupational limit (ICSC 1614, 2005), which means no value has been set there, not that exposure is harmless. Check each target market before you commit.
Why do 2-butoxyethanol exposure limits differ between OSHA, NIOSH and ACGIH?
2-Butoxyethanol exposure limits differ between OSHA, NIOSH and ACGIH because each body set its value at a different time, for a different purpose and with different legal force. The US OSHA PEL is 50 ppm as an 8-hour TWA, Cal/OSHA's is 20 ppm and the NIOSH REL is 5 ppm (OSHA Annotated Table Z-1, NIOSH values as of 2021).
The OSHA PEL is the enforceable US federal limit, and OSHA states that PELs "are 8-hour time weighted averages (TWAs) unless otherwise indicated" (OSHA Annotated Table Z-1). The NIOSH recommended exposure limit (REL) is a recommendation for "up to 10-hour time weighted averages (TWAs) during a 40-hour work week" (OSHA Annotated Table Z-1). ACGIH's threshold limit value (TLV) is 20 ppm averaged over an 8-hour workshift (New Jersey Department of Health, 2008), and the ILO-WHO card lists the same 20 ppm TLV (ICSC 0059, 2024). The EU sets 20 ppm as an 8-hour TWA and 50 ppm short term (ICSC 0059, 2024).
Formulators should design to the strictest limit in any market they sell into, not the US federal one. Every one of these limits covers air only. The New Jersey fact sheet warns that "When skin contact also occurs, you may be overexposed, even though air levels are less than the limits listed above" (New Jersey Department of Health, 2008). That is why the EU and the cards carry a skin notation, flagging skin as an exposure route.
What do you need to retest after replacing 2-butoxyethanol in a cleaner?
After replacing 2-butoxyethanol in a cleaner, you need to retest phase stability, cleaning result, drying and residue, flash point and the label classification, each against the original product. Run every check on the final blend, not on the neat candidate: water, surfactants and builders change how the solvent behaves.
The table below decides whether the reformulated cleaner matches the original on each check. The pass criteria are illustrative; replace them with your own specification.
Check | Pass | Fail and what to do |
|---|---|---|
Phase stability, concentrate and use dilution, through freeze-thaw and warm storage | Clear, one phase, no separation (illustrative) | Cloud or split: raise the miscible candidate or add hydrotrope, then repeat |
Cleaning result on your own soils and substrates | Equal to the original side by side (illustrative) | Weaker: check solvency, raise candidate level or change candidate |
Drying and streaking on the target surface | No longer than the original, no streaks (illustrative) | Slower: blend in a faster candidate, recheck flash point |
Flash point of the finished blend, closed cup | Same category as the original or safer (29 CFR 1910.1200 Appendix B) | Stricter category: change candidate before any label work |
Label and SDS classification | Updated from the new composition | Mismatch: correct the SDS before release |
Flash point is the check that stops a trial. A blend that cleans well but drops into Category 3 needs new storage, labelling and transport review. Measure it with a closed-cup method the US Hazard Communication Standard accepts, such as ASTM D56, ASTM D3278 or ASTM D93 (29 CFR 1910.1200 Appendix B). ASTM D93-26 covers petroleum products from 40 °C to 370 °C (ASTM D93-26), so confirm with your laboratory which method suits a water-based blend. In Lubinpla, a formulation design task reviews replacement candidates by the role each ingredient plays, routes them through a safety review and sets the scope of revalidation.
Frequently asked questions
Is propylene glycol n-butyl ether a drop-in replacement for 2-butoxyethanol?
No. PnB has a similar flash point, 63 °C closed cup, but only moderate water solubility of 6 g/100 mL (ICSC 1614, 2005), while 2-butoxyethanol is miscible with water (ICSC 0059, 2024). To keep a concentrate clear, it usually needs a hydrotrope or a second, fully miscible glycol ether.
Do you need to change the SDS after replacing 2-butoxyethanol?
Yes. The SDS lists composition, flash point and exposure limits, and all three change when the solvent changes. Under the US Hazard Communication Standard, classification follows the mixture's own data, including its flash point (OSHA, 29 CFR 1910.1200 Appendix B). Update the SDS and label before the new product ships.
Can you reduce 2-butoxyethanol instead of removing it?
Yes. Australia's assessment recommended reduction as a minimum: "At the very least, the 2-butoxyethanol content in cleaning products should be reduced to concentrations where the risk to human health is minimal" (NICNAS, 1996). It also suggested replacing spray application with a liquid stream. A partial cut still needs the stability and cleaning retests.