Coating Warranty Claim: The Evidence the Maker Needs
Summary
Preparing a coating warranty claim takes four steps: match the defect definition, collect application records, add dated photos and test results, and state the suspected cause. The manufacturer accepts the claim when that evidence shows three things: a covered defect, notice inside the warranty deadline, and an application that followed the product data sheet.
One roof coating warranty requires written notice within 30 days of the leak, with a description and the original purchase receipt (Amrize Building Envelope, 2025).
The same warranty voids coverage if batch numbers are invalid, the coating was installed after its storage stability period, or it was not installed per the product data sheet (Amrize Building Envelope, 2025).
ASTM D610-25 rates rusting on painted steel on a 0 to 10 scale based on the percentage of visible surface rust (ASTM, 2025).
ASTM D4541-22 says pull-off results with the same coating are likely to vary when any test parameter changes (ASTM, 2022).
Warranty terms differ by maker, product and term, so the warranty document for your product decides what counts; this guide shows what to collect, not what any one maker will accept. It covers industrial, protective and roof coatings sold with a written material warranty, not consumer paint guarantees or legal advice on a dispute.
What does a coating manufacturer need before accepting a warranty claim?
Before accepting a warranty claim, a coating manufacturer needs four things: a defect the warranty actually covers, proof the claim was filed on time, records showing the coating was applied as the product data sheet directs, and evidence that points to the product rather than the substrate or the work. Collect them in this order:
Read the warranty and copy its defect definition, notice deadline, exclusions and eligibility conditions into the claim file, with the date you found the failure.
Send written notice before the deadline, to the address the warranty names. One warranty states that notifying "a contractor, a re-seller, or an authorized Gaco sales representative is not notice to Warranty Services" (Amrize Building Envelope, 2025).
Collect the application records: product and batch numbers, purchase receipt, surface preparation, ambient conditions and dry film thickness.
Photograph, rate and test the failure, then write the suspected cause as a hypothesis with evidence for and against.
Do not repair or recoat the failed area until the manufacturer has seen it or agreed in writing. The failed film is the evidence. The same warranty can ask for three 12 x 12 in (about 300 x 300 mm) samples, two from the suspected area and one from another area, with removal costs not covered (Amrize Building Envelope, 2025).
How does the coating warranty define a defect or failure?
Each coating warranty defines a defect or failure in its own words, and the claim must describe the failure in those words, not in general terms such as "the coating failed". A material warranty is on the coating product itself, so what it usually covers is a manufacturing defect, not every change in appearance or every leak.
One roof coating warranty, for example, warrants that the coating "will not leak as a result of a manufacturing defect" (Amrize Building Envelope, 2025). The same document excludes leaks traced to a failure of the substrate or to improper substrate preparation as directed on the product data sheet, and it "does not cover discoloration, reflectivity, blistering, installation, or workmanship in the application of the Coating" (Amrize Building Envelope, 2025). Under that warranty, a blistered roof with no leak is outside coverage, however bad it looks.
Before writing the claim, check three parts of the warranty:
The covered event: leak, loss of adhesion, rusting to a stated degree, chalking or color change beyond a stated rating.
The exclusions: substrate, surface preparation, workmanship, ultraviolet exposure without a topcoat, products from other makers.
The eligibility conditions: registration, valid batch numbers, application inside the shelf life and minimum film thickness for the term.
Where the warranty names a rating, such as a rust grade, describe the failure with the standard it names. The manufacturer then reads your result on its own scale.
Which application records does the coating manufacturer ask for?
The manufacturer asks for records showing the product was applied the way its product data sheet directs, because the warranty's exclusions and eligibility conditions turn on them. One warranty excludes leaks traced to improper substrate preparation and is void if the coating was not installed per the data sheet (Amrize Building Envelope, 2025). Without those records, the manufacturer cannot rule out the application as the cause.
For each coat, gather:
Product name, batch numbers and purchase receipt. One warranty is void if submitted batch numbers are invalid or the coating was purchased or installed after its storage stability period (Amrize Building Envelope, 2025).
Surface preparation: method, cleanliness grade reached, profile and who inspected it.
Ambient conditions at application: air temperature, relative humidity, surface temperature and dew point, with times. ASTM E337-15(2023) covers measuring air humidity from wet- and dry-bulb readings (ASTM, 2023).
Dry film thickness readings per coat and in total, with gauge type and verification. ASTM D7091-22 notes that "most manufacturers of high performance coatings will warranty coating systems based upon, in part, achieving the proper thickness of each layer and the total coating system" (ASTM, 2022).
Mixing ratio, thinning, induction time and recoat intervals used.
Minimum thickness can decide coverage outright: one warranty table sets 22 mils (about 560 micrometers) dry film thickness as the minimum for a 10-year term on its S20 Series product (Amrize Building Envelope, 2025). When a distributor passes the claim on, the same facts make a usable complaint; see what manufacturers need from a distributor complaint.
How should you photograph and date a coating failure?
Photograph a coating failure so that a reviewer who never visits the site can locate each defect, judge its size and see when it was found. Close-ups with no date and no location are weak evidence in a coating claim: nobody can match them to the structure or to the notice date.
For each failed area, shoot in this order:
A wide shot that shows the whole structure or elevation and where the failed area sits.
A mid shot of the failed area with a fixed landmark, such as a weld seam, a drain or a gridline number.
Close-ups with a ruler or scale card in frame, so blister size, crack length or rust spread can be measured.
The same close-up framing on a sound area of the same coating system, for comparison.
Keep the camera's original files with their date and time data, and log each photo with its number, area, date and photographer. Mark the locations on a drawing or plan.
If the failure progresses, repeat the same shots. Photograph each test spot before and after testing, because destructive tests leave damage the manufacturer will ask about.
Which tests support a coating failure claim?
Tests support a coating failure claim when they rate the failure on a standard scale the manufacturer recognizes and measure properties the product data sheet states. Ratings turn "bad blistering" into a number both sides can check.
Rusting on painted steel: ASTM D610-25 evaluates the degree of rusting on a "zero to ten scale based on the percentage of visible surface rust" and classifies distribution as spot, general, pinpoint or hybrid rust (ASTM, 2025).
Blistering: ASTM D714-25 describes "the size and density of the blisters so that comparisons of severity can be made" using photographic reference standards; when used as a specification, the permissible degree is agreed between purchaser and seller (ASTM, 2025).
Other defects: ISO 4628-1:2016 sets the system for designating the quantity and size of defects and the intensity of changes in appearance, intended in particular for defects caused by ageing and weathering (ISO, 2016).
Adhesion on metal: ASTM D4541-22 measures pull-off strength; fracture occurs along the weakest plane of fixture, glue, coating and substrate, and the fracture surface shows where (ASTM, 2022). Concrete uses ASTM D7234 instead.
Report the method, instrument type and conditions with every result. ASTM D4541-22 states that results with the same coating are likely to vary when the glue, fixture size, cure time, pull rate or device changes, and that the test method used must be identified when reporting (ASTM, 2022).
For pull-off tests, also record which layer failed. A fracture surface inside the substrate or primer points away from the topcoat.
How do you state the suspected cause of a coating failure without overclaiming?
State the suspected cause of a coating failure as a hypothesis with evidence for and against it and the test that would settle it, not as a finding. A claim that says "the coating is defective" invites the manufacturer to reject all of it on the first exclusion that fits; one that weighs causes invites a technical review.
Give each candidate cause its own row, including causes that would fall under an exclusion. The template below shows the form; its content is illustrative.
Suspected cause | Evidence for | Evidence against |
|---|---|---|
Product defect in one batch (illustrative) | Failure only where batch B was used | Same batch sound on the north wall |
Low film thickness (illustrative) | Two readings below the data sheet minimum | Most readings within range |
Condensation at application (illustrative) | Surface temperature close to dew point on day 2 | No failure on areas coated on day 2 |
The most useful row is the one that names a check: for the batch row, a retained sample test by the manufacturer would confirm or rule out the product.
List the evidence against each cause honestly. The manufacturer will find it anyway, and a claim that already addresses it is harder to dismiss. Lubinpla handles this as an escalation decision built from your own data sheets and field records: it holds the suspected cause as a hypothesis with evidence for and against, settles which facts go to the manufacturer, and returns one cited document for you to approve.
Coating warranty claim evidence check before sending
Use the check below to decide whether a coating warranty claim is ready to send. Each row is tied to the exclusion or condition it answers. Send the claim only when every row has its evidence, or a stated reason why it is missing.
Evidence | What the manufacturer checks | If missing |
|---|---|---|
Warranty defect definition and notice date | Covered event; notice within the deadline, such as 30 days (Amrize Building Envelope, 2025) | Claim can be refused on notice alone |
Batch numbers and purchase receipt | Valid batch, inside storage stability, original buyer | Eligibility cannot be confirmed |
Surface preparation and ambient records | Preparation and conditions per the product data sheet | Preparation exclusion is assumed |
Dry film thickness readings per coat | Minimum for the term, such as 22 mils for 10 years on one product (Amrize Building Envelope, 2025) | Thickness becomes the likely cause |
Dated photos with locations | Extent, location and timing of the failure | Extent and date are disputed |
Degradation ratings and adhesion results | Rating on the named scale; failing layer | Severity is a matter of opinion |
Retained samples and failed film | Lab test of product against specification | Product defect cannot be confirmed |
Start with the first row. A covered defect and on-time notice to the right address come before any test, because one warranty gives the maker no obligation if the owner fails to give proper notice to Warranty Services (Amrize Building Envelope, 2025).
Read the remaining rows against the exclusions in your own warranty. Where a row is empty, say so in the claim and give the reason, for example that film thickness was not recorded at application. Then offer the nearest substitute, such as thickness measured now on sound areas next to the failure.
Keep a copy of everything you send, with the date and recipient, and ask the manufacturer to confirm receipt in writing.
Frequently asked questions
Can I repair a failed coating before the manufacturer inspects it?
Make safety repairs only, and document the area first with photos, ratings and samples. Ask the manufacturer in writing before recoating: a repaired area removes the evidence the warranty review needs and may conflict with the warranty's notice and inspection terms.
Who files the coating warranty claim, the owner or the applicator?
The warranty names who may claim. Material warranties are often issued to the building or asset owner and may not be assignable; one roof coating warranty is "not transferable or assignable in any manner" (Amrize Building Envelope, 2025). The applicator usually supplies the application records.
Does a lab report have to come from an independent laboratory?
Most material warranties do not require one, but an independent report on retained and field samples carries more weight when the parties disagree. Agree on the methods with the manufacturer before testing so both sides accept the results.