Lubinpla

Metalworking coolant gone bad: what to ask on the first call

Summary

A first call about a metalworking coolant problem comes down to six questions: symptom, machine and material, recent changes, concentration and pH, top-up practice, and sample availability. They apply to water-miscible coolants in machine sumps. The answers decide which test kit, samples and records you bring, so the visit starts from a likely cause.

  • HSE guidance for water-mix metalworking fluids says to measure concentration with a refractometer and pH every week, and recommends keeping tramp oil below 2% (HSE MW5, 2021).

  • HSE reads dip slide results at or above 10^6 CFU/ml as poor control, which normally means draining and cleaning the system (HSE, 2024).

  • One fluid maker states that most water-based metalworking fluids are designed to operate at pH 8.5 to 9.5 (Master Fluid Solutions, 2026).

  • NIOSH recommends an exposure limit of 0.4 mg/m3 thoracic particulate mass for metalworking fluid aerosols, as a time-weighted average for up to 10 hours per day in a 40-hour week (OSHA, 2001).

These questions fit water-miscible coolants (soluble oil, semi-synthetic and synthetic) in single machines and central systems. Straight oils take no concentration or pH reading, so a call about one turns to water ingress, oxidation and mist. A worker with a rash or breathing symptoms needs occupational health advice, not only a fluid test.

What should you ask on the first call about a metalworking coolant problem?

Ask six questions in a fixed order, and write each answer down before you suggest a cause.

  1. Symptom. What do the operators see, smell or feel, since when, and on how many machines?

  2. Machine and material. Which machine type, sump size and filtration, and which metals are being cut?

  3. Recent changes. What changed in the 4 weeks before the problem started: product batch, water, machine, material, cleaner or shift pattern? The 4-week window is an illustrative starting point.

  4. Concentration and pH. What do today's refractometer and pH readings show, and what do the last month's records show for concentration, pH, tramp oil (leaked machine oil) and dip slides?

  5. Top-up practice. Who tops up, with what water, and as premix, water alone or concentrate alone?

  6. Samples. Can the customer keep a sample from the problem sump and one from a sump that works, without draining either?

The order matters. The first three answers report what the customer saw. The last three are measured facts you can check. If the readings in step 4 contradict the symptom in step 1, start the visit with the measurement method, since a misread refractometer can hide a concentration problem. Ask for numbers with units and dates, not "normal" or "fine".

Which coolant symptoms should you ask the customer to describe?

Have the customer describe the symptom in plain terms: odor, color, foam, rust, residue, and skin or breathing complaints, and whether it affects one machine or all of them. Each symptom points to a different first test.

OSHA's best practices manual says a bad smell usually means uncontrolled microbial growth, and that fluid turning gray or black often means bacteria are present, while a yellow or brown tint suggests tramp oil (OSHA, 2001). The same manual says sulfates in the water promote sulfate-reducing bacteria that produce a "rotten egg" odor (OSHA, 2001).

Excessive foam has many causes in that manual: soft water with some products, too high a concentration, contamination by cleaners, or a low sump level that draws air into the pump (OSHA, 2001). Too high a concentration may also cause dermatitis and heavy residues, while too low a concentration may lead to corrosion and bacterial growth (OSHA, 2001).

Ask when the symptom started, whether it gets worse after a weekend or a shutdown, and whether it shows on the parts, the machine or both. A smell that appears only on Monday morning points to a sump that stood still. Rust on parts but not on the machine points as much to the part's path after machining as to the coolant.

Which machine, material and recent changes matter for a coolant complaint?

The machine, the metals cut and anything that changed shortly before the problem matter most, because together they decide which contaminants can enter the sump.

Ask for the machine type, whether it runs on its own sump or a central system, the sump volume in liters, and the filtration or skimming in place. Find out which hydraulic, way lube and spindle oils the machine uses and whether any of them leak, since OSHA's manual says tramp oil often comes from hydraulic or way lube systems leaking into the fluid and that it feeds microbes (OSHA, 2001).

Ask for the metals being cut, including any new alloy, coated part or casting, because staining of the machined metal is one of the problems OSHA lists for investigation (OSHA, 2001).

Then ask what changed: a new coolant batch or product, a new water source or softener, a new machine or repair, a new parts washer chemical, a longer shutdown, or a new person doing the top-ups. A complaint that starts the week after a change often traces to that change, so record the date of each change next to the date the symptom started.

Ask for the product name and its technical data sheet (TDS), which gives the concentration range and refractometer factor you will need on site.

Which concentration and pH readings should the customer take before the visit?

Ask the customer to take a refractometer concentration reading and a pH reading before the visit, from the problem sump and from one sump that works, and to send the last month of records. HSE guidance asks for both readings every week for water-mix fluids, measured against the supplier's recommended levels (HSE MW5, 2021).

The refractometer reading needs care. Blaser Swisslube says to zero the refractometer with water first, and that for some fluids the scale reading must be multiplied by the product-specific refractometer factor to get the actual concentration (Blaser Swisslube, accessed 2026). The same page says a diffuse reading line means the emulsion is unstable or heavily loaded with tramp oil (Blaser Swisslube, accessed 2026), so ask whether the line was sharp.

For pH, one fluid maker states that most water-based fluids are designed to operate at pH 8.5 to 9.5 and that below 8.0 bacteria can multiply quickly (Master Fluid Solutions, 2026). Treat that as a general range and check the product's own TDS. Ask whether the pH came from a meter or from strips, and when the meter was last calibrated.

A pH that falls over several weeks tells you more than a single low reading, which is why the record matters as much as today's reading.

How does top-up practice change a metalworking coolant complaint?

Evaporation, drag-out and the make-up water all shift concentration and water chemistry between readings, so the way a site tops up can change the whole complaint. HSE guidance notes that water-mix fluids evaporate and become more concentrated in use, so it says to top up only with fluid below the recommended concentration (HSE MW5, 2021). OSHA's manual says a sump level 30% below the full mark shows fluid loss or water evaporation, and that the concentration should be checked before adding water or premix (OSHA, 2001).

Ask who tops up, how often, with what, and whether each addition is written down. The OSHA manual says all system additions should be controlled and recorded by a designated person (OSHA, 2001).

Then ask about the water: mains, well, softened, reverse osmosis or deionized. OSHA says calcium and magnesium in hard water form scale and insoluble soap scum with many fluids, and that sulfates and chlorides are corrosive and contribute to rust (OSHA, 2001).

A Master Fluid Solutions article adds that concentration that keeps climbing despite water-only top-offs means evaporation is exceeding drag-out (Master Fluid Solutions, 2026). If the customer adds concentrate and water separately by eye, expect the concentration to swing, and plan to measure each sump on site.

What should you bring to a metalworking coolant site visit?

Pack the test kit and sample containers that the first-call answers point to, plus the TDS and safety data sheet (SDS) of the coolant and of any biocide or cleaner the site uses. The table below shows what goes in the bag for each answer from the call.

Question to ask

What the answer points to

Bring to the visit

Odor: rancid or rotten egg?

Microbial growth; sulfate in water (OSHA, 2001)

Dip slides, pH meter, water test strips

Rust on parts or machine?

Low concentration, chlorides or sulfates (OSHA, 2001)

Refractometer, water hardness and chloride strips

Foam?

Soft water, high concentration, cleaner, low level (OSHA, 2001)

Refractometer, sample of the parts washer fluid

Sticky residue?

High concentration, hard water scum (OSHA, 2001)

Refractometer, water hardness strips

Skin complaints?

High concentration, high alkalinity, tramp oil (OSHA, 2001)

Refractometer, pH meter, coolant SDS

Machine and material

Tramp oil source, metal staining

Way lube and hydraulic oil names, part sample

Recent changes

The change that came just before the symptom

Change dates, old and new TDS

Concentration

Out of TDS range; diffuse line means tramp oil (Blaser Swisslube, accessed 2026)

Refractometer, product factor from TDS

pH

Below the TDS range: microbial activity likely

Calibrated pH meter, buffers

Top-up water and method

Concentration swing, hard water

Water sample bottle, top-up log

Bring clean, labeled sample bottles for each problem sump, one working sump and the make-up water, so a laboratory can run the tests the field kit cannot.

The odor row is the one that most often changes the visit plan. A rancid or rotten egg smell means dip slides go in the bag, and HSE reads results at or above 10^6 CFU/ml as poor control that normally needs draining and cleaning (HSE, 2024).

When you sample, wear the gloves and eye protection that the coolant SDS names, and stir the sump first so tramp oil does not coat the dip slide (HSE MW5, 2021).

How do you check first-call coolant answers against what you find on site?

Check each first-call answer against a measurement or record on site, and note where the two differ. The difference is often the finding.

Measure concentration and pH yourself in the same sumps the customer measured, using both the customer's instrument and yours, and compare. If the readings match but the symptom persists, the cause likely lies in water, tramp oil or bacteria rather than in the mix. Read the top-up log against the sump levels, and the change dates against the date the symptom started.

ASTM E1497-23, the practice for selecting and safely using metal removal fluids, covers product selection, storage, dispensing and maintenance (ASTM E1497-23, clause 1.1). That scope gives a useful frame for the questions you add after the visit.

Write the six questions, the customer's answers and your measurements in one record per call, with dates and units, so the next engineer on the account sees what was asked and what was found. A shared layout for those records is covered in one customer visit report template for every engineer.

In Lubinpla, the six intake questions can go into the organization's one work log template, so every first-call record uses the same fields. The template applies only to work logs its agent writes, not to ones a person enters on the writing screen.

Frequently asked questions

Should the customer drain the coolant sump before the visit?

Ask the customer to keep a sample from the sump before any draining, labeled with the machine and date. If dip slides already show poor control or workers report symptoms, the site may need to act at once under its own risk assessment. The sample still lets you test what caused the problem.

Can a refractometer reading alone confirm coolant concentration?

Not always. The reading needs the product's refractometer factor from the TDS, and tramp oil or an unstable emulsion blurs the line. When the line is diffuse or the result does not fit the symptom, confirm with titration, the second concentration method fluid makers name (Master Fluid Solutions, 2020). Run it the way the fluid supplier specifies.

Who should join the first call about a coolant problem?

Ask for the person who tops up the sumps and the person who maintains the machines. The first knows the water, the additions and the readings. The second knows leaks, filters and recent repairs. A purchasing contact alone usually cannot answer the six questions.

Related posts