Lubinpla

How to get operators to log coolant concentration correctly

Summary

Getting accurate coolant logs from operators takes 4 steps: fix the sampling time and point, apply the refractometer factor, trim the log fields, and show the readings back. The steps assume a water-miscible metalworking fluid read with a handheld refractometer, with the supplier giving the product factor and the target range for each machine.

  • HSE guidance for UK machine shops recommends measuring water-mix fluid concentration with a refractometer and pH every week, and keeping records of all tests for at least five years (HSE MW5, 2021).

  • A product with 20% water in the concentrate will read 8.0 at best on a refractometer at a 10% dilution, so a raw reading is not the concentration (Quaker Houghton, 2020).

  • In Germany, TRGS 611 calls for nitrite in used water-mixed coolant to be measured weekly, with up to four weeks allowed after three consecutive documented results below 10 mg/l (BAuA TRGS 611, 2007).

  • The best analog refractometers reach an accuracy and precision of about plus or minus 0.2 Brix units (STLE, 2011).

This guide covers operator logging of water-miscible metalworking fluids measured with a refractometer in individual machine sumps or central systems. It does not cover laboratory methods such as titration, straight oils, or how a supplier interprets the history. Target ranges, factors and test intervals come from the product data sheet and the rules of your jurisdiction.

Why do operator coolant concentration logs go wrong?

Operator coolant concentration logs usually go wrong for one of three reasons: the reading was taken at the wrong time or place, the raw Brix value was written down as the concentration, or the operator wrote the number expected instead of the number seen. Each gives a tidy log that does not describe the sump.

The refractometer factor comes first. A refractometer reads % Brix, not concentration, and the product factor converts one into the other. Quaker Houghton puts it plainly: "Some people believe that a reading of “5” means 5.0%. It does only if the product is 100% active" (Quaker Houghton, 2020).

Contamination is the second cause. Tramp oil also refracts light, so refractometers tend to read higher than the actual concentration over time, and a heavily contaminated sump may give no clear line at all (Master Fluid Solutions, 2019).

Timing is the third. A reading taken right after a top-up, before the fluid has mixed, describes the top-up, not the system.

Guessed values are harder to spot. A log with the same number every shift, or with every entry exactly on target, suggests the readings were not taken.

What do you need before operators start logging coolant concentration?

Before operators start logging coolant concentration, they need a working refractometer, the product's refractometer factor and target range posted at each machine, distilled or deionized water for zeroing, a fixed sampling point, and a log sheet with only the fields that matter. Without the factor and range at the machine, an operator cannot tell a good reading from a bad one.

Take the factor and the operating range from the supplier's product data sheet. Each supplier should provide a chart of refractometer readings over the normal concentration range for its product (Quaker Houghton, 2020). Post the factor, the range and the sump capacity on the machine; the HSE example record sheet carries the same items at the top of each sheet (HSE MW5, 2021).

A 0-10 Brix scale has more graduations than a 0-32 scale, so it reads low concentrations more precisely (Quaker Houghton, 2020).

HSE guidance says those carrying out fluid checks should be trained on the equipment, the procedure, how to record and interpret results, and the remedial actions to take (HSE MW5, 2021). Coolant is a skin hazard, so hand out the gloves named in the coolant's safety data sheet (SDS) before the first round.

How do you set up operator coolant logging, step by step?

Setting up operator coolant logging takes four steps, and each one removes a usual cause of a bad entry.

Before step 1, zero the refractometer with distilled or deionized water. Blaser Swisslube advises setting the zero point with high quality water before measuring the emulsion (Blaser Swisslube, accessed 2026). STLE reports that manufacturers recommend calibrating analog units before each use, while many users calibrate only the first time (STLE, 2011).

  1. Fix the time and point. Pick one moment in the shift and one sampling point per machine, such as the return line or a sample valve, where the coolant is circulating and the operator can reach it without entering the guarded area. Write both on the machine. Do not sample at a nozzle near a running spindle: HSE notes that gloves increase the risk of entanglement at moving machinery (HSE MW5, 2021).

  2. Apply the factor. The operator writes the raw Brix reading and the corrected concentration, which is the reading times the product factor, so a reviewer can check the arithmetic.

  3. Trim the fields. Keep only the fields in the log section below. Every extra field is one more place to guess.

  4. Show readings back. Put each machine's readings on a simple trend next to its target range, and tell operators what changed because of them.

How should operators apply the refractometer factor to a coolant reading?

Operators apply the refractometer factor by multiplying the raw Brix reading by the product factor from the supplier's data sheet, then recording both numbers. The HSE example record sheet defines concentration as the refractometer reading times the fluid correction factor (HSE MW5, 2021).

The level of active ingredients in the concentrate dictates the factor, and each product has its own (Quaker Houghton, 2020). A product that is not fully active reads lower than its true dilution, so a raw value logged as concentration makes a correct sump look lean.

Keep three rules at the machine. Use the factor for the product in that sump, and replace the posted factor the same day the product changes. Write the raw value before converting it, so an arithmetic slip can be found later. Do not round toward the target: a sump reading 4.6% against a 5-8% range (illustrative) goes in the log as 4.6%, because the reviewer needs that difference.

Record a blurred line as blurred. Blaser Swisslube notes that a diffuse reading means the emulsion is unstable or heavily loaded with tramp oil (Blaser Swisslube, accessed 2026). That is a finding to report, not a number to guess.

When in the shift should operators check coolant concentration?

Operators should check coolant concentration at a fixed point early in the shift, with the coolant circulating, and not right after a top-up.

An STLE article on troubleshooting metal-removal fluids states that concentrations should be checked at the start of every shift (STLE, 2022), and a machine-shop maintenance checklist also lists a refractometer check each shift (Oxmaint, 2026). Other guidance sets a lower minimum: Blaser Swisslube advises a check whenever the tank is filled up and a recorded value at least once a week (Blaser Swisslube, accessed 2026), and HSE recommends weekly concentration and pH measurement (HSE MW5, 2021).

The fixed time matters most. Each morning's reading at one point then compares with yesterday's.

After a top-up or correction, wait before reading again. The STLE article advises retesting after the fluid has recirculated long enough to turn over the system at least twice, based on its volume and pumping rate (STLE, 2022).

Sample fluid that is moving. Settled fluid at the bottom of a still sump, or the film of tramp oil on its surface, gives a reading that does not represent what reaches the tool.

Which fields does an operator coolant log really need?

An operator coolant log needs about eight fields per entry: date and time, machine, operator initials, raw Brix, corrected concentration, pH if measured, action taken, and a note box. Product, factor, target range and sump capacity go in the sheet header, filled once, not on every line.

The HSE example sheet uses the same split: machine, asset reference, product, sump capacity, correction factor and operating ranges sit in the header, and the rows carry concentration, pH, dipslide results, and comments and actions taken (HSE MW5, 2021). The table below lists what an operator fills in each time.

Field

Who fills it

Why it stays

Date and time

Operator

Shows the agreed time was kept

Machine

Operator

Ties the reading to one sump

Operator initials

Operator

Shows who read it, for follow-up

Raw Brix reading

Operator

Lets a reviewer check the factor

Corrected concentration

Operator

Reading times the product factor (HSE MW5, 2021)

pH

Operator, if the site tests it

Weekly by HSE guidance (HSE MW5, 2021)

Action taken and amount

Operator

Explains the next reading

Note

Operator

Blurred line, smell, foam, tramp oil

The raw Brix field matters most for checking: without it, nobody can tell whether the factor was applied. Machine and initials let a supervisor trace a doubtful entry to one sump and one person. Tool life or part counts belong in other records. Where nitrite testing applies, as under TRGS 611 in Germany, keep the nitrite results with the same machine's log (BAuA TRGS 611, 2007).

How do you check an operator coolant log entry?

An operator coolant log entry can be trusted when it was taken at the agreed time and point, shows both raw Brix and corrected concentration, follows a zero check, and gives the actual value, not one rounded to the target. The check table below decides whether an entry stands or needs a new reading.

Check

Pass

Fail and what to do

Time and point

Agreed time, circulating fluid

Taken after a top-up or from a still sump: take a new reading

Raw Brix and factor

Both written, arithmetic matches

Only one number: ask which it is, retake if unsure

Zero check

Zeroed with distilled or deionized water that round

Not zeroed: zero and retake

Value as read

Varies from day to day

Same value every shift or exactly on target: read it together at the machine

Clear line

Sharp boundary in the eyepiece

Blurred: note it and report tramp oil or instability

The fourth row catches most bad logs. A column of identical numbers is rarely a real sump, because evaporation, carry-off on chips and top-ups move concentration from day to day.

Supervisors should check a few entries each week against their own reading at the same machine and point. A failed entry shows which setup step needs repeating, such as a missing factor at the machine or a hard-to-reach sampling point, not who to blame. When a third party takes the readings, HSE guidance says the site should still review the results and the remedial actions taken (HSE MW5, 2021).

How do you show operators what their coolant readings changed?

Showing operators what their coolant readings changed means putting each machine's readings on a trend against its target range and telling them what was done because of a reading. Operators log carefully when they see the log used. HSE guidance recommends keeping records in a table or graph so trends are easy to spot and act on (HSE MW5, 2021).

Go through the trend at a weekly shift meeting. Point to one or two readings that led to an action, such as a top-up with leaner premix after concentration rose from evaporation, or a skimmer run after a blurred line. An engineer quoted by STLE describes the purpose of daily records as picking up trends to take action before major problems occur (STLE, 2011).

For how a supplier can collect plant readings without retyping them, see collecting site readings from customers without retyping. In Lubinpla, a plant contact can enter coolant readings in a Field Care site data request; the readings become project records once the supplier's team approves them, and the supplier can share the measuring procedure document with that contact through Field Care.

Frequently asked questions

Should operators top up coolant with water or with concentrate?

Operators should top up with premixed coolant, not plain water or neat concentrate. HSE notes that water-mix fluids become more concentrated as water evaporates, so top-ups should be mixed below the recommended concentration (HSE MW5, 2021). Check the supplier's data sheet for the premix ratio.

Is a digital refractometer worth it for operator logging?

A digital refractometer removes the scale reading, the step operators most often misread. STLE reports digital units at about plus or minus 0.1 to 0.2 Brix units, with temperature compensation, and some can be programmed to show concentration directly (STLE, 2011). Confirm that the programmed factor matches the product in use.

What should operators do when the coolant reading is out of range?

Operators should retake the reading at the agreed point after the fluid has circulated, confirm the factor, and then follow the posted action for that machine. If the value is still out of range, record it as read and report it to the person named for coolant before adding anything.

Related posts