How to write a technical data sheet for an industrial chemical
Summary
An industrial chemical technical data sheet needs 7 sections: identity, description and uses, typical properties with test methods, application conditions, storage, packaging and revision data. Unlike the safety data sheet (SDS), it has no format fixed by regulation. The sheet earns trust when every value is labeled typical or specification and names its test method and condition.
Who reads an industrial chemical technical data sheet, and what do they decide?
An industrial chemical technical data sheet is read by the people who decide whether to trial, approve or buy the product: process and application engineers, quality staff, purchasing and, at the supplier, technical service and sales. Each of them takes a different decision from the same page, so each section has to serve one of those decisions.
The application engineer decides whether the product fits the process: dosage, temperature, compatible materials and the properties that predict performance.
Quality decides which values go into an incoming inspection or a purchase specification. It needs to know which numbers the supplier will certify for each lot.
Purchasing compares two products and needs values measured by the same test methods under the same conditions.
Technical service and sales treat the sheet as the agreed public statement of what the product is. A claim that is not on the sheet should not appear in a quote or an email.
The page also travels beyond these readers. A distributor forwards it, a customer pastes values into its own specification, an auditor files it with the approval record, and a competitor reads it. Write for a reader who has only this page and no one at the supplier to ask. If the same content has to reach both a customer and a manufacturer's technical team, how to write a technical report for customer and manufacturer covers what each audience needs.
Which sections does a technical data sheet template for an industrial chemical need?
A technical data sheet template for an industrial chemical needs seven sections, in this order: identity, description and uses, typical properties with test methods, application conditions, storage, packaging and revision data. The order runs from what the product is to how to use and keep it, which is also the order in which a reader screens a product. Keep the sheet to one or two pages per grade. A family of grades can share one sheet only when every value is given per grade.
Use the table below to decide whether a draft sheet is ready to publish. For each section it lists what the section must show and the evidence that has to exist before anyone writes it.
Section | What it must show | Evidence behind it |
|---|---|---|
Identity | Product name, code, grade, chemical type, supplier | Product master record; same identifier as SDS section 1 |
Description and uses | What the product is and does, main applications, limits of use | Application trials, customer approvals |
Typical properties with test methods | Property, value labeled typical or specification, unit, method with edition, condition | Results from several lots; release test limits |
Application conditions | Concentration or dosage range, temperature range, compatible materials, mixing order | Trial reports, field records |
Storage | Storage temperature range, shelf life and its start date, sensitivity to frost or moisture | Stability data |
Packaging | Pack sizes and pack materials | Packaging specification |
Revision data | Revision number, date, what changed, pointer to the SDS | Document control record |
The properties row carries the most risk. A published packaging-industry guideline orders each property as "Property, test method, value, units", followed by standard deviation or sample size if available (IoPP Medical Device Packaging Technical Committee, undated). The same order works for chemicals with one column added: whether the value is typical or a specification limit.
Application conditions carry the next highest risk, because trials fail first where a temperature or concentration range is missing.
How should a technical data sheet separate typical values from specification limits?
A technical data sheet should separate typical values from specification limits by labeling every value as one or the other in the value cell itself. List as specifications only the limits the supplier tests and certifies for each lot. The two promise different things: a typical value describes past production, while a specification limit is a promise checked on every batch.
Standards bodies draw the same line. An IEC technical report that tabulates typical values for laminated sheets states: "The purpose of these typical values is to give general guidance and should not be considered as specification requirements." (IEC TR 60893-4:2014+A1:2017, BSI product page). Unlabeled values invite a customer to treat a typical value as a guarantee and reject a good lot.
Specification limits tie the data sheet to the certificate of analysis, the document that reports test results for each lot. In pharmaceutical active ingredient manufacturing, ICH Q7 says the certificate "should list each test performed in accordance with compendial or customer requirements, including the acceptance limits, and the numerical results obtained" (ICH Q7, 2000). ICH Q7 covers active pharmaceutical ingredients, not industrial chemicals, but the same logic carries over: every specification row on the data sheet should match a row the certificate reports.
State how a result is compared with a limit, and write each limit with the digits that comparison uses. ASTM E29-22 aims "to outline methods which should aid in clarifying the intended meaning of specification limits", and a reference to it is valid only when the absolute method or the rounding method is chosen (ASTM E29-22).
How should a technical data sheet state test methods and conditions?
A technical data sheet should state, for every property, the full test method designation with its edition year, the condition under which the value was measured, and the unit. With all three, a reader can reproduce the number or compare it with another supplier's. A viscosity without a temperature, or a flash point without the method, cannot be compared.
Four rules cover most sheets, whether the methods are ASTM, ISO, DIN or in-house:
Name the method with its edition, such as ASTM D445-26, and before release confirm on the publisher's page that this edition is the active one.
Give the condition next to the value: temperature, concentration, shear rate, cure schedule or sample preparation.
Respect each method's scope. ASTM D93-26 covers flash point of petroleum products from 40 °C to 370 °C by a Pensky-Martens closed-cup tester (ASTM D93-26), so a value outside that range or for another material needs another method.
Where an in-house method is used, make the procedure available. The packaging guideline says "Where unique test methods are used, test method procedures should be made readily available." (IoPP Medical Device Packaging Technical Committee, undated).
Write values in SI units first, with other units in brackets if customers need them. Keep the same unit for the same property across every grade in a product family. The SI Brochure states that "a space is always used to separate the unit from the number", so 30.2 °C, not 30.2°C (BIPM SI Brochure, 9th edition, 2019).
What belongs on the technical data sheet and what belongs on the SDS?
Hazard information belongs on the safety data sheet, and performance information belongs on the technical data sheet. Where both cover the same property, the values must agree, and the technical data sheet should point to the SDS rather than repeat hazard statements. The SDS is regulated; the technical data sheet is not.
In the US, OSHA requires that an SDS "shall include the information specified in Table D.1 under the section number and heading indicated for sections 1-11 and 16" (OSHA 29 CFR 1910.1200 Appendix D). Other jurisdictions set their own SDS rules, so check the format required where the product is sold. No general regulation sets a format for the technical data sheet, so the supplier's own document control has to keep its content consistent with the SDS.
The table below shows where each kind of content goes.
Content | Technical data sheet | Safety data sheet |
|---|---|---|
Hazard classification and statements | No; point to the SDS | Section 2 (OSHA 29 CFR 1910.1200 App D) |
Physical and chemical properties | Properties that predict performance, labeled, with method | Section 9 list, including flash point, pH and kinematic viscosity (OSHA 29 CFR 1910.1200 App D) |
Handling and storage | Storage for product quality and shelf life | Section 7, safe handling and storage, including incompatibilities (OSHA 29 CFR 1910.1200 App D) |
Uses | Applications, dosage, compatible materials | Section 1, recommended use and restrictions (OSHA 29 CFR 1910.1200 App D) |
Revision date | Yes | Section 16, date of preparation or last revision (OSHA 29 CFR 1910.1200 App D) |
Watch the physical and chemical properties row most closely. A flash point or viscosity printed on both documents must be the same number from the same method, or the customer's safety reviewer will stop the trial.
What does an illustrative technical data sheet property block look like?
An illustrative technical data sheet property block lists one property per row: the value, its label as typical or specification, the unit, and the test method with edition and condition. The block below describes an imagined mineral-oil-based metalworking concentrate. Every value in it is illustrative, not data for any real product.
Set out like this, the labels, units and method designations let a quality reader see at once which rows will appear on the certificate of analysis.
Property | Value and label | Unit | Test method and condition |
|---|---|---|---|
Appearance | Clear amber liquid, typical (illustrative) | none | Visual, 20 °C |
Kinematic viscosity | 30.0 to 36.0, specification (illustrative) | mm²/s | ASTM D445-26, 40 °C |
Kinematic viscosity | 5.6, typical (illustrative) | mm²/s | ASTM D445-26, 100 °C |
Flash point | 180 minimum, specification (illustrative) | °C | ASTM D93-26 Procedure A, closed cup |
Density | 0.88, typical (illustrative) | g/cm³ | In-house method QC-03, 15 °C |
Read viscosity at 40 °C (illustrative) first. It is the one property given as a range and labeled specification, so the certificate of analysis reports it for each lot, with the rounding method stated. At 100 °C the same property is typical only, which tells the reader it is not tested on every batch.
The density row uses an in-house method, so its procedure must be available on request. A one-line footnote under the block can say that typical values are not specifications.
Why do industrial chemical technical data sheets fail the reader?
Industrial chemical technical data sheets fail the reader when they mix typical values and specification limits without labels, omit test methods or conditions, contradict the SDS, or go out of date without a revision record. Each failure pushes a decision off the page and into an email thread, which slows trials and approvals.
Common failure patterns:
Unlabeled values. The customer copies a typical value into a purchase specification, a lot falls just outside it, and the delivery is rejected.
Methods without editions. A value measured under an older edition of a test method is compared with one from the current edition, and nobody can tell whether a difference is real.
Missing conditions. A viscosity, a cure time or a pH is given without temperature or concentration.
Contradictions with the SDS. The flash point on the data sheet differs from SDS section 9.
Marketing claims in the properties block. Words such as "excellent" or "superior" in a value column are not properties and cannot be tested.
Stale sheets. The formula or the supplier of a raw material changed, the SDS was revised, but the data sheet kept its old date.
The release checklist below has a check for each of these. Most are cheaper to prevent at writing time than to correct after a customer has copied the values into its own specification.
What should a technical data sheet checklist cover before release?
A technical data sheet checklist before release should confirm the seven sections, the labels and methods on every value, agreement with the SDS and the certificate of analysis, and the revision record. Run it at each creation or revision, and have it signed by someone other than the author.
Before release, confirm that:
The product identifier matches SDS section 1 and the product master record.
All seven sections are present, with uses and their limits.
Every value is labeled typical or specification, and every specification row has a matching row on the certificate of analysis.
Every specification limit states the digits used for comparison and, where ASTM E29-22 is referenced, the absolute or rounding method.
Every property names a test method with its edition, checked as active on the publisher's page on the day of release, and the measurement condition.
Values fall inside each method's stated scope; in-house methods are available on request.
Units are SI first, spaced from the number.
Properties that appear on both documents match SDS section 9 exactly.
No hazard statements are copied; the sheet points to the current SDS.
Storage gives a temperature range and the start date of shelf life.
The revision number, date and a one-line change note are filled in.
In Lubinpla, document writing fills the missing facts in a draft like this from the company's own records first, then from public sources, and asks the user only once, for whatever neither source has.