Lubinpla

Lap shear test failure modes: when an adhesive failure qualifies

Summary

To qualify a lap shear bond, check test validity, strength against the specification minimum, and failure mode against ISO 10365 classes, or ASTM D5573 for fiber-reinforced plastic joints. A bond that passes on strength but fails adhesively, meaning at the interface, is not yet proven. It flags a surface preparation risk that needs a cause and a durability retest.

This guide covers qualifying adhesive bonds from single-lap shear coupons, such as ASTM D1002 for metals, when strength and failure mode disagree. It does not cover design allowables, which lap shear coupons cannot supply, or failure inside a weak substrate. Where a customer or industry specification states a failure mode limit, that limit governs over this guide.

When does lap shear failure mode decide bond qualification?

Lap shear failure mode decides bond qualification whenever the test is used to approve a surface preparation, primer or adhesive for production. Strength alone cannot show whether the interface will last. ASTM D1002-10(2019), the active metal-to-metal lap shear method, states: "This test method is primarily comparative. However, it does have application as a discriminator in determining variations in adherend surface preparation parameters and adhesive environmental durability" (ASTM, 2019). When the test judges how the adherend, the part being bonded, was prepared, read the strength together with the evidence of where the joint broke.

Failure mode also tells you what the number measured. A 2016 study of experimental adhesives explains: "A cohesive failure measures the intermolecular bond strength within the adhesive, while adhesive failures measure the bond between the adhesive and the adherend" (Kozowyk et al., 2016). Two coupons with the same strength can therefore be measuring different things: one the adhesive, the other the weakest part of the surface.

Three moments call for this guide: qualifying a new adhesive or surface preparation; a change of supplier, substrate or process; and a production check that passes on strength while the fracture surfaces show bare adherend. Each time, write the failure mode criterion into the test plan before coupons are bonded, so the result cannot shape the rule.

What do adhesive, cohesive and mixed lap shear failure modes mean?

Adhesive, cohesive and mixed lap shear failure modes describe where a bonded coupon broke: at the interface, inside the adhesive, or partly in each. The National Physical Laboratory (NPL) defines adhesive failure as "Failure of an adhesive bond, such that separation appears to be at the adhesive/adherend interface", and cohesive failure as "Failure within the body of the adhesive (i.e., not at the interface)" (NPL, 2023). A third outcome is adherend failure, where the break runs inside the bonded material itself.

Two standards supply the names for these patterns. ISO 10365:2022 "specifies the designations for the main types of failure pattern of bonded assemblies" and applies to all mechanical tests on a bonded assembly (EVS, 2022). The 2022 edition replaced ISO 10365:1992 and added failure with stress whitening of the adhesive (SWCF) and debonding due to bondline corrosion (COR) (BSI, 2022). ASTM D5573-99(2019), written for fiber-reinforced plastic joints, classifies adhesive, cohesive, thin-layer cohesive, fiber-tear, light-fiber-tear, stock-break and mixed failures, and its examples report mixed failure as percentages, such as 32% adhesive and 68% fiber-tear (ASTM, 2019).

The thin-layer case matters for qualification because it is easy to misread. A PPG patent defines thin-film cohesive failure as "A thin layer of adhesive clinging to one broken surface", intermediate in desirability between adhesive and cohesive failure (PPG, 2001). ASTM D5573 classifies by eye "without the aid of a microscope or other means to magnify the surface" (ASTM, 2019), so a surface that looks bare can still carry a thin adhesive film. Record the class and the share of each mode per coupon.

How much cohesive failure should a lap shear specification require?

A lap shear specification should state a minimum cohesive failure share for the bond in question, because the test methods themselves set none. ASTM D5573-99(2019) says it "does not address the acceptability of any specific failure mode" (ASTM, 2019). Test laboratories report "Type of failure (cohesive or adhesive) and percentage" for ASTM D1002 coupons (Intertek, accessed 2026). The pass line for that percentage, though, comes from the specification or from the agreement between supplier and user.

We found no public general minimum cohesive percentage for lap shear. The clearest published limit belongs to a different test: the US Air Force Research Laboratory (AFRL) wedge test criteria for surface preparations pass at "≥95% Cohesive Failure (Within Adhesive) with Interfacial Failure Only At Edges" after exposure under its preferred conditions of 60 °C (140 °F) and 95 to 100% relative humidity, and grade 90 to 95% cohesive as marginal (AFRL, 2004). That limit is AFRL's own for the ASTM D3762 wedge test, which the same presentation notes is not standardized for exposure or pass/fail; copying it into a lap shear specification needs the agreement of the parties.

In commercial practice the rule is often qualitative rather than a number. The PPG patent calls cohesive failure "the most desirable mode of failure" and states that bare-metal failure "is undesirable and will usually result in disqualification of a lubricated substrate candidate from commercial application" (PPG, 2001). When you write the limit, name three things: the classification standard, how the share is estimated, and whether thin-layer cohesive failure counts as cohesive.

Why can lap shear strength pass while the bond fails at the interface?

Lap shear strength can pass while the bond fails at the interface because a fresh joint can carry its test load through a weak interface that moisture and service conditions have not yet attacked. The apparent shear strength of a single-lap coupon reflects geometry, adherend stiffness and peel stresses as well as adhesion. ASTM D1002-10(2019) warns that this strength "may differ from that obtained from a joint made with different adherends or by a different bonding process" (ASTM, 2019). Set a strength minimum below what a good interface delivers, and a poor interface can meet it.

The weak interface shows itself in durability testing. An AFRL presentation to an FAA bonded structures workshop calls surface preparation the "single most important factor (and most common root cause of failures)" and names moisture attack at the interface as the primary problem for metal adherends (AFRL, 2004). The same presentation states that shear tests "as currently practiced" are "not sufficient, even if conducted hot/wet with moisture-saturated bonds" for judging environmental durability (AFRL, 2004).

The NPL guide makes the link to failure mode: "Unsatisfactory surface preparation will result in the bond failing adhesively and unpredictably at the adhesive/adherend interface" (NPL, 2023). That link suggests that interfacial failure in a dry, room temperature lap shear test is an early warning. The strength number says the joint held this time; the bare surface says it may not hold after ageing.

How do you judge lap shear failure mode when the specification is silent?

When the specification is silent on failure mode, judge the lap shear result against criteria fixed before the test, taken in order. Record a strength pass with adhesive failure as a finding that changes the conclusion. The table below gives each criterion, its threshold and source, and the next step. Thresholds without a source are agreed in the test plan.

Criterion

Threshold (source)

If met

If not

Test valid: geometry, bondline and cure as planned; break in the adhesive, not the adherend

Failure should occur in the adhesive, not the substrate (Intertek, accessed 2026)

Judge strength

No verdict; fix and repeat

Strength at or above the specification minimum

Value in the specification or agreement

Judge failure mode

Not qualified

Cohesive share, classed per ISO 10365:2022 (ASTM D5573-99(2019) for FRP joints)

Agreed share; one wedge test limit is at least 95% cohesive (AFRL, 2004)

Judge durability

Hold; investigate surface preparation

Adhesive failure traced to a surface preparation cause

Cause found, corrected and retested

Retest with corrected preparation

Not qualified

Durability after conditioning

Agreed exposure; one wedge test runs 28 days at 60 °C and 95 to 100% RH (AFRL, 2004)

Qualify

Not qualified

The cohesive share row carries the most weight. A coupon set that clears the strength minimum but falls below the agreed cohesive share is held, not passed, until a cause is found and a retest shows cohesive failure.

Read the rows from the top. A failed validity or strength row ends the judgment, and a failed cohesive share sends you to the cause row rather than to a verdict. The order matters because a strength figure from an invalid run carries no weight, and a failure mode judged before strength wastes a retest.

Estimate the cohesive share per coupon, not as an average across the set. One coupon with bare metal over the overlap points to a local preparation fault that an average hides. Agree in advance who makes the call on borderline shares and how thin-layer cohesive failure is counted. A result that passes one criterion and fails another needs its own handling, set out in what to do when a chemical trial result only partly passes.

Which surface preparation faults cause adhesive failure in lap shear tests?

Four surface preparation faults most often cause adhesive failure in lap shear tests: contamination left on the adherend, contamination added after preparation, delay before bonding, and a preparation that does not suit the metal or its service environment. The NPL guide states that surface preparation exists "to remove surface contaminants (grease and dust), increase surface area for bonding, promote micro-mechanical interlocking, and/or chemically modify a surface" (NPL, 2023). When preparation misses any of these aims, the miss can show up as bare adherend.

Handling after preparation is a frequent cause. NPL advises that prepared adherends "must not be exposed to physical handling or uncontrolled atmospheric environments" and that "It is advisable that bonding be performed immediately following surface treatment to maximise performance" (NPL, 2023). Rolling or forming oils on steel are another: the PPG patent tested adhesion on lubricated steel and treated bare metal on the fracture surface as adhesive failure (PPG, 2001).

The preparation must also match the metal. ASTM D2651-01(2024) covers procedures for preparing wrought metal surfaces for bonding, not cast metals, and states that the surface preparation for qualification and quality control testing "should be agreed upon by both manufacturer and user" (ASTM, 2024). To confirm the cause, examine both fracture surfaces. NPL notes that X-ray photoelectron spectroscopy (XPS) is frequently used for quantitative elemental analysis of fracture surfaces (NPL, 2023).

Chemical surface treatments use hazardous chemicals; follow each product's SDS and local workplace rules, such as COSHH in the UK, as NPL notes (NPL, 2023).

Worked example: a lap shear result that passes strength but fails adhesively (illustrative)

The worked lap shear example below uses illustrative values to show how the criteria table turns a split result into a decision. A plant qualifies a structural epoxy on abraded and solvent-wiped steel. The test plan sets a strength minimum of 15 MPa and a cohesive share of at least 80% on every coupon (illustrative values agreed in the plan, not from a standard). Five ASTM D1002 coupons average 21 MPa, all above 15 MPa, but three show bare steel over most of the overlap (illustrative).

Step 1, validity, in this illustrative run: bondline, cure and alignment match the plan, and no coupon broke in the steel, so the run is valid. Step 2, strength: every coupon passes. Step 3, failure mode: three of five fall below 80% cohesive, so the set is held, not qualified. The record puts both facts side by side: strength met, failure mode not met.

Step 4, cause: the preparation log shows the abraded coupons waited overnight before bonding, and the three adhesive failures came from the batch wiped with a reused cloth (illustrative). Both match the contamination and delay faults in the NPL guide (NPL, 2023). Step 5, retest: new coupons are bonded after a fresh wipe, within the time the adhesive maker recommends. If they fail cohesively, a conditioned retest follows before approval, because AFRL reports that marginal preparations can pass at 1 hour and 24 hours and still fail at 28 days in the wedge test (AFRL, 2004).

How should you report a lap shear verdict with adhesive failure?

A lap shear verdict with adhesive failure should be reported as held or not qualified, with the passing strength and the failing failure mode stated side by side rather than merged into one pass. For each coupon, record the maximum load, the shear strength, the failure mode class and the estimated share of each mode, which is what laboratories report for ASTM D1002 (Intertek, accessed 2026). Name the classification standard, ISO 10365:2022, or, for fiber-reinforced plastic joints, ASTM D5573-99(2019), so a reader can repeat the call.

State the test conditions alongside the numbers. ASTM D4896-01(2024) warns that misusing strength values from single-lap test methods such as D1002 "as allowable design-stress values for structural joints could lead to product failure, property damage, and human injury" (ASTM, 2024). A report that lists a strength without the adherend, preparation, bondline, cure and test temperature invites that misuse.

Keep the finding separate from the verdict. Write the failure mode result as its own line, with photographs of both fracture surfaces, the suspected cause, and the retest that would close it. When the question goes to a customer or manager, the decision they face is whether to accept a known interface risk, and the report should make that risk visible.

Lubinpla's test result evaluation follows the same order: it checks test validity first, judges the result against each criterion fixed in advance, and records a result that could change the conclusion as a separate finding in one cited document for your review.

Where this lap shear verdict does not apply

A lap shear verdict on failure mode does not apply where the test cannot separate interface weakness from other effects, or where another rule governs. First, a break inside a weak substrate, such as some plastics or wood, measures the substrate, not the bond; a 2016 study on beech plywood found that porosity made adhesive and cohesive failure hard to tell apart (Kozowyk et al., 2016). Second, fiber-reinforced plastic joints have their own classes in ASTM D5573-99(2019), including fiber-tear failure, which is not an interface fault (ASTM, 2019).

Third, a customer, aerospace or automotive specification with its own failure mode limit replaces the agreed thresholds in this guide. Fourth, lap shear coupons do not qualify a design: ASTM D1002-10(2019) warns against using its strength values as design-allowable stresses (ASTM, 2019). Fifth, a pass here is not a durability pass. For aluminum, ASTM D3762-24, the wedge test, is described by ASTM as "correlatable with service performance in a manner that is much more reliable than conventional lap shear or peel tests" (ASTM, 2024). A bond intended for wet service therefore needs that test or an agreed conditioned retest.

International work uses ISO 4587:2003 for tensile lap-shear strength of rigid-to-rigid bonded assemblies, which ISO last reviewed and confirmed in 2021, and placed under systematic review in July 2026 (ISO, 2026). The order of the criteria in this guide applies to it in the same way.

Key takeaways

  • A lap shear bond that passes strength but fails adhesively is held, not qualified, until the cause is found and a retest fails cohesively.

  • The classification standards set no acceptable failure mode share (ASTM D5573 says so directly); the specification or test plan must.

  • Fix the cohesive share, the classification standard and the treatment of thin-layer failure before coupons are bonded.

  • Interfacial failure in a dry lap shear test is an early sign of a surface preparation problem that conditioning can expose.

  • Report strength and failure mode as separate results, with photographs of both fracture surfaces.

  • Confirm durability with a wedge test or an agreed conditioned retest before approving a bond for wet service.

Related posts