How to measure rust preventive film weight on parts (g/m2)
Summary
Measuring rust preventive film weight takes 4 steps: weigh the coated part, strip the film in solvent, reweigh, then divide the mass loss by the coated area. The g/m2 figure holds only if the balance resolves far below the film mass, a second strip confirms the film is gone, and the target range was agreed before the first reading.
One patent sets 0.01 to 10 g/m2 for a rust preventive oil film on phosphate-treated steel sheet and prefers 0.5 to 3 g/m2 (US Patent 6,509,099, 2003).
Above 10 g/m2 on that sheet, the same patent reports that degreasing ends insufficiently and paint adhesion suffers (US Patent 6,509,099, 2003).
A common magnetic film thickness probe is specified at ±(1 µm + 1%) from 0 to 50 µm (DeFelsko, 2026), close to the 1.1 µm average of a 1 g/m2 oil film at 0.9 g/cm3 (illustrative).
In a laboratory trial, one 5-minute immersion at 96 °F (36 °C) removed 83 to 99.8 percent of a heat-dried rust preventive per steel coupon, depending on the cleaner (TURI Cleaning Laboratory, 2004).
This method covers oil, wax and solvent-cutback rust preventive films (products thinned with a solvent carrier that evaporates) on metal parts and test panels. It does not cover conversion coatings, paint or metallic coatings, which have their own gravimetric and thickness standards.
What do you need before measuring rust preventive film weight on parts?
Five things must be in place before the first weighing: a balance that resolves far below the expected film mass, a reliable coated area, a stripping solvent with its safety data sheet (SDS), a fixed conditioning time, and a target g/m2 range agreed with the supplier.
Start by checking the balance against the film mass. A 1 g/m2 film on a part with 0.01 m2 of coated area weighs only 10 mg (illustrative). A balance that reads to 1 mg can then show the film only in steps of 10 percent, while one that reads to 0.1 mg gives a 1 percent step (illustrative). The balance must also carry the whole part, which rules out heavy parts on most analytical balances.
Take the coated area from the drawing or the CAD model, not from the outline, and decide in advance whether bores, threads and blind holes count.
Fix the conditioning, meaning the time and temperature between coating and weighing, and match it to production. Solvent-cutback products lose mass as the carrier evaporates.
Choose a stripping solvent that the rust preventive's SDS or technical data sheet names as a remover, and read the solvent's own SDS, sections 7 and 8, for handling and protective equipment. Record all of these on the test sheet before the first part is weighed.
How do you measure rust preventive film weight by weighing before and after degreasing?
The film weight is a difference in mass. Weigh the coated part, strip the film in solvent, dry and reweigh the bare part, then divide the mass difference by the coated area. Gravimetric coating mass methods such as ISO 3892:2000 for conversion coatings and ASTM A428/A428M-21 for aluminum coatings determine coating mass per unit area by weighing, but they do not cover oil films, so state your own method on the report.
Weigh the coated part after the agreed conditioning time and record its mass as m1, in grams. If you can weigh the bare part before coating, record that as m0 and use it as a cross-check.
Strip the film by immersing the part in the chosen solvent for a fixed time, for example 5 minutes (illustrative). Follow the solvent SDS, sections 7 and 8, and, in the United States, the flammable liquid rule, which covers any liquid with a flashpoint at or below 93 °C (OSHA, 29 CFR 1910.106).
Dry the part to constant mass and record m2. Then strip, dry and reweigh a second time. If the mass drops again by more than one balance step, the first strip was incomplete, so use the lower mass.
Calculate the film weight as (m1 minus m2) divided by the coated area in m2. Report the result in g/m2 together with the conditioning time, solvent and area method.
When should you use test panels instead of real parts to measure rust preventive film weight?
Panels are the right sample when the part is too heavy for a balance that resolves the film, when its area cannot be calculated, or when you are comparing products rather than accepting a production coating. To accept a production lot, the real part is the better sample, because the film on the part is what has to protect it.
Panels give a known area and a light, repeatable sample, which is why humidity cabinet testing of rust preventives uses steel panels. ASTM D1748-24 covers "the relative abilities of metal preservatives to prevent the rusting of steel panels under conditions of high humidity" (ASTM D1748-24). The same standard calls its data "of interest only in eliminating the most unsuitable materials or for indicating a probable relative order of protection" (ASTM D1748-24).
A flat panel does not drain like a part. Oil collects in recesses, threads and lower edges and runs thin on vertical faces and sharp edges, so a panel reading is likely to differ from the part average. If you use panels, coat and drain them the same way as the parts, hang them in the same orientation, and record that the result describes the panel, not the part.
How accurate are thickness gauges for rust preventive oil films?
For most rust preventive oil films, contact coating thickness gauges (magnetic or eddy current) are not accurate enough. The film is only a few micrometres thick, and the gauge tolerance is of the same size. One common magnetic gauge probe is specified at ±(1 µm + 1%) over 0 to 50 µm (DeFelsko, 2026).
Converting film weight to average thickness shows the problem. Thickness in µm equals film weight in g/m2 divided by density in g/cm3. A 1 g/m2 film of an oil with a density of 0.9 g/cm3 averages about 1.1 µm (illustrative), so a ±1 µm tolerance is about as large as the film itself. A 3 g/m2 film averages about 3.3 µm (illustrative), still close to the tolerance.
Non-contact oil film sensors used on strip lines do read in g/m2. They still have to be calibrated against weighed samples of the same oil and substrate, so the gravimetric method sets the reference either way.
Contact probes also press into a soft or wet film, and gauges are calibrated for solid coatings on a defined substrate. Treat a gauge reading on an oil film as a rough check that some film is present, and settle acceptance by weight.
Supplier figures need the same caution. Data sheets often state a film figure without the method behind it: one product data sheet lists "Film Thickness" as "4.0 ± Gm/Sq M" with no test conditions (Apar Industries, 2021). Ask how such a number was measured before you compare your result with it.
How do you set a target rust preventive film weight range before measuring?
Agree two limits before anything is weighed. The lower limit gives enough protection for the storage or shipping condition; the upper limit is what the next process can tolerate. Write both into the specification together with the method. A range agreed after the readings tends to move to fit them.
The patent literature shows where each limit comes from. For a rust preventive oil film on phosphate-treated steel sheet, one patent states that below 0.01 g/m2 "the effect of rust-preventive oil application cannot be attained" and that above 10 g/m2 "the degreasing ends insufficiently, which results in poor coating adhesiveness" (US Patent 6,509,099, 2003). The same patent prefers 0.5 to 3 g/m2 (US Patent 6,509,099, 2003). Those values apply to that sheet and its painting line, not to every part.
For your own parts, base the lower limit on the supplier's recommendation and a corrosion test of coated parts at a known film weight. Base the upper limit on cleaning, painting, assembly or dripping limits downstream. Write the range down with the conditioning time, stripping solvent, area method and sample size, so every later reading is judged against the same rule.
How do you check a rust preventive film weight result?
Before a reading is used to accept or reject a coating, confirm five points: the balance step, the area, the stripping, the sample type and the pre-set range. The check table below decides whether a reading can be used to accept the coating.
Check | Pass | Fail and what to do |
|---|---|---|
Balance resolution | Balance step at or below 1 percent of the film mass on the part (illustrative) | Step too coarse: use a finer balance or a larger coated area per weighing |
Coated area | Area from drawing or CAD, with bores and threads decided in advance | Area estimated from outline: recalculate before reporting g/m2 |
Stripping completeness | Second strip changes mass by no more than one balance step | Mass drops again: extend stripping, repeat, report the lower mass |
Panel versus part | Sample type matches the purpose: parts for acceptance, panels for comparison | Panel used for acceptance: repeat on parts or label the result as panel only |
Result against range | Inside the g/m2 range written before testing | Outside range: hold the lot, check the application step, retest |
The stripping row catches the most common error. If a second strip still removes mass, the first result understated the film. The range row works only if the range, the conditioning time and the solvent were written down before the parts were weighed; a range chosen afterwards tends to be fitted to the readings. Keep each reading tied to its part number, coating date and sample position.
A film weight reading is also the evidence you need when a customer reports rust and you must show whether the coating was in specification. The method for that kind of case is set out in how to show whether a product complaint is really the product.
When should you ask a coatings lab about rust preventive film weight?
Bring in a coatings or analytical lab when your balance cannot resolve the film on the part, when the part has inaccessible internal surfaces, when the film is a wax or a dried solvent-cutback product that one solvent does not remove, or when the result will settle a dispute with a customer or supplier.
A lab can weigh larger parts on a balance with finer resolution, measure the coated area of complex shapes, and test which solvent removes a given film completely. It can also extract the film from a known area and analyze it, which helps when the question is whether the right product was applied, not only how much. For a dispute, ask the lab to report the conditioning time, solvent, number of strips, balance resolution and area method, so both sides can repeat the test.
Plan the comparison before the results come in. Lubinpla's performance evaluation fixes the coating weight criterion and the measurement method before any result is entered, and ties each result to its sample for the verdict. Whatever tool you use, keep the agreed range, the method and each sample's identity in one record, so a later reading is compared with the same rule.
Frequently asked questions
How many parts should you weigh to check rust preventive film weight?
Weigh at least three parts per coating condition (illustrative), taken from the start, middle and end of the run, because film weight varies with drain time, part orientation and bath condition. Report the mean and the range. One part shows only that a film exists, not that the process holds the agreed range.
Can you measure rust preventive film weight on parts that were already in storage?
Yes, but the result describes the film after storage, not the film as applied. Solvent-cutback films lose their carrier, and oil films can drain or be wiped off during handling. Note the storage time and conditions on the report. If the question is the application process, compare with freshly coated parts.
Why do rust preventive film weight results differ between two labs?
Results differ when the labs use different conditioning times, solvents, numbers of strips or area methods. A wax film that one solvent removes only partly gives a lower reading. Agree the full method in writing and exchange one shared sample before comparing routine results.