Switching to a non-etching aluminum cleaner: what to check first
Summary
Choose an inhibited non-etching alkaline cleaner when anodizing or bright finishes cannot tolerate etch, and an etching cleaner only when the next step needs fresh metal. Before switching a conversion coating, anodizing or paint line, run the candidate at your alloy, temperature, concentration and dwell, then check weight loss, smut and a water-break-free rinse (ASTM F22-21).
Henkel's EP0201864 can cleaner runs at pH 11.0 or higher, most preferably 11.5 to 12.3, and reports that earlier cleaners built on alkali metal hydroxides etched aluminum cans extensively and irregularly (Henkel, EP0201864B1, 1992).
Henkel states that the etching effect of its low-etch BONDERITE C-AK 212 cleaner can be altered with changes in temperature and concentration, within an operating range of 38 to 85 °C (Henkel product page, 2026).
In mild alkaline etching before plating, the etch rate depends more on temperature than on caustic concentration (Atotech, US5669980, 1997).
ASTM F22-21 describes the water-break test as not quantitative and typically restricted to go or no-go evaluation of cleanliness (ASTM F22-21, 2021).
This guide covers spray and immersion alkaline cleaning of wrought and cast aluminum ahead of anodizing, conversion coating or painting. It does not cover acid etching, deoxidizing or steel and mixed-metal phosphate lines, and it gives no universal etch limit, because no published numeric threshold defines a non-etching aluminum cleaner.
What makes an alkaline cleaner etch aluminum?
An alkaline cleaner etches aluminum once its free alkalinity, temperature and contact time are high enough to dissolve the natural oxide film and then the metal under it. A review of corrosion in water-based metalworking fluids notes that alkaline media corrode metals, with aluminum as the example: the protective aluminum oxide film dissolves in alkaline solution first (Li et al., 2022). A mild cleaner is still alkaline; what differs is how fast it attacks.
Free caustic (sodium or potassium hydroxide) drives etch hardest. Henkel's can-cleaner patent records that cleaners built on alkali metal hydroxides gave extensive and irregular etching of aluminum containers, and cites an earlier cleaner with at least 6 g/l of sodium or potassium hydroxide at about pH 13 as far more than desirable and a cause of smutting (Henkel, EP0201864B1, 1992). Smut is the film of oxides and undissolved alloying elements left on the surface.
Temperature and concentration come next. Henkel says the etching effect of its low-etch BONDERITE C-AK 212 can be altered with changes in temperature and concentration (Henkel product page, 2026), and an Atotech plating patent states that mild alkaline etch rate depends more on temperature than on caustic concentration (Atotech, US5669980, 1997).
Dwell time, how long parts stay in contact with the cleaner, is the factor lines forget. In the Henkel patent's account of earlier alkaline can cleaners, cans that stood wet after a line stop developed severe staining, and spray times of 60 to 120 seconds, against the usual 10 to 60 seconds, might also stain (Henkel, EP0201864B1, 1992). A cleaner that is non-etching at the normal dwell can still mark parts during a stoppage.
Which inhibitors and builders keep an aluminum cleaner non-etching?
Two kinds of ingredient keep an aluminum cleaner non-etching: silicate inhibitors protect the metal, and mild builders keep free caustic low, so soil comes off without much aluminum dissolving. An Ecolab patent notes that alkali metal silicates have been used as corrosion inhibitors since the mid-20th century and remain in use as comparatively effective inhibitors for aluminum and aluminum alloys (Ecolab, US9222176B2, 2015).
In a sodium bicarbonate blast-cleaning system for aircraft, Church and Dwight found that sodium silicate at about 100 to 1000 ppm substantially reduced or prevented alkali attack on 7075-T6 aluminum, while below 100 ppm it was generally not effective and above 1000 ppm it was likely to gel (Church and Dwight, US5232514, 1993). The same patent reports that the inhibited system did not adversely affect the adhesion of primer and paint.
Silicate has a cost. Ecolab records that silicate residues left by insufficient rinsing, or by solution drying on warm surfaces, form tenacious layers that are very difficult to remove (Ecolab, US9222176B2, 2015). Some cleaners sold for anodizing lines are non-silicated: Henkel lists BONDERITE C-AK 298 Aero as non-silicated and free rinsing, for use before anodizing and conversion coating (Henkel via Chempoint, 2026).
Phosphate builders need a closer look than the label. Henkel's patent uses inorganic phosphates against brown staining in a bath most preferably at pH 11.5 to 12.3 (Henkel, EP0201864B1, 1992), while Church and Dwight cites prior work showing orthophosphates can damage and discolor aluminum (Church and Dwight, US5232514, 1993). The two findings point different ways, so test the full formula.
How do aluminum alloys differ in etch and smut response?
Alloys differ because the alloying elements an alkaline cleaner does not dissolve stay on the surface as smut, and how much stays depends on the alloy. Atotech describes the film left after a mild caustic etch as a mixture of aluminum oxides, alloying element oxides and exposed silicon, and states that its tenacity varies with the composition of the aluminum (Atotech, US5669980, 1997).
Silicon-rich castings show the effect most clearly. In aluminum-silicon alloys, the aluminum is etched preferentially over the silicon, leaving coarse silicon crystals exposed on the surface that a desmut step has to remove (Atotech, US5669980, 1997). A cleaner that is mild on a 6xxx extrusion can therefore leave smut on a silicon die casting.
High-copper alloys are another special case. Axalta's aviation pretreatment data sheet says its phosphoric acid aluminum cleaner should not be used on high-copper alloys such as 2024 or on aluminum castings, and names a separate cleaner for them (Axalta, 2015). That cleaner is acid, not alkaline, but the pattern holds: suppliers qualify cleaners alloy by alloy.
ASTM D1730-09(2020), the practice for preparing aluminum surfaces for painting, makes the same point in general terms: the quality produced by any surface preparation method may vary with different alloys (ASTM D1730-09R20, 2020). Treat every alloy series on the line as its own trial, castings included.
How clean must aluminum be for anodizing, conversion coating or painting?
Before anodizing, conversion coating or painting, aluminum must be clean enough to give a water-break-free surface. The downstream specification then decides whether that is enough or whether the oxide also has to be removed. ASTM F22-21 states that a water-break-free test is commonly used for in-process verification of the absence of contaminants that may interfere with priming, conversion coating, anodizing, plating or adhesive bonding (ASTM F22-21, 2021).
The term has a working definition. Axalta's data sheet describes it as water sheeting out completely over the metal surface, with any beading or breaks meaning the surface must be cleaned again (Axalta, 2015). Henkel's can-cleaner patent sets the same condition before conversion coating and lacquer (Henkel, EP0201864B1, 1992).
The test has limits. ASTM F22-21 says the method is not quantitative, that it can detect molecular layers of hydrophobic organic contaminants when properly conducted, and that its sensitivity may drop on very rough or porous surfaces (ASTM F22-21, 2021). For a number, the standard points to contact angle methods (ASTM F22-21, 2021).
Removing oils is not the same as removing oxide. ASTM D1730-09(2020) notes that solvent cleaning does not disturb the natural oxide film, and lists alkaline cleaners among the chemical treatments (ASTM D1730-09R20, 2020). If your anodize or conversion coat specification calls for deoxidizing, a non-etching cleaner does not replace that step.
Which non-etching aluminum cleaner fits each line condition?
Three things decide which cleaner fits: the downstream step, the alloy and how long parts can stay wet. The table maps common aluminum line conditions to a cleaner type, with the reason drawn from the sources above.
Your conditions | Cleaner type | Why |
|---|---|---|
Anodizing or bright finish, wrought alloys, light oils | Inhibited mild alkaline non-etching cleaner, non-silicated where the anodize or conversion coat supplier requires it or rinsing is weak | Silicate residue is hard to remove after poor rinsing (Ecolab, US9222176B2, 2015) |
Conversion coating or paint, light oils and oxide | Low-etch mild alkaline cleaner run at the low end of its range, 38 to 85 °C for one such cleaner (Henkel product page, 2026) | Etch rises with temperature and concentration (Henkel product page, 2026) |
Silicon die castings | Non-etching cleaner, with a desmut step ready if any etch occurs | Etching leaves exposed silicon and smut (Atotech, US5669980, 1997) |
High-copper alloys such as 2024 | Cleaner qualified for that alloy by its supplier | Suppliers exclude 2024 from some aluminum cleaners (Axalta, 2015) |
Heavy soils, light etch acceptable before a deoxidizer | Inhibited caustic or etching alkaline cleaner, followed by desmut | At least 6 g/l of hydroxide near pH 13 will cause smutting (Henkel, EP0201864B1, 1992) |
Line stops leave parts wet with cleaner | Cleaner with stain control and a short dwell | Cans standing wet after line stops stained with earlier cleaners (Henkel, EP0201864B1, 1992) |
The silicon casting row matters most. A cleaner trialed only on extrusions can pass and then smut every casting, so put the alloy with the most silicon or copper in the trial set.
Two rows are about the line rather than the part. The heavy-soil row accepts some etch on purpose: a stronger alkaline cleaner removes the soil, and a deoxidizer or desmut step after it removes the smut. For that row, the switch question is whether the second step is already in place.
The line-stop row covers the risk that trials miss. A cleaner that passes at a normal dwell can stain parts left wet during a breakdown. Ask the supplier how the product behaves at long contact times, and test that case before approving it.
How do you trial a non-etching aluminum cleaner before switching?
Trial a non-etching aluminum cleaner on test coupons of every alloy you process, at your worst-case temperature, concentration and dwell. Compare it with the current cleaner on weight loss, smut, water-break and downstream results. The steps:
Record the current cleaner's operating window and the alloys, soils and downstream specification for each part family.
Read the candidate's technical data sheet (TDS) and safety data sheet (SDS). Make up the bath and handle the concentrate with the protective equipment SDS section 8 names, and plan disposal of the spent bath under your local wastewater discharge permit.
Weigh coupons, immerse them at the top of the temperature and concentration window and at twice the normal dwell, then reweigh and inspect them. ASTM F483-09(2020) uses this combination of weight change and visual change under total immersion (ASTM F483-09R20, 2020).
Wipe each coupon with a white cloth to check for smut.
Rinse and run the ASTM F22-21 water-break test on each coupon.
Process real parts through anodizing, conversion coating or painting and test them to your specification.
Treat supplier etch figures as claims until your coupons confirm them; see why a product that meets the TDS specification can still fail on site.
Lubinpla's product recommendation pins down the alloy, soil and downstream requirements first, then compares the candidates' TDS values from the data room with their sources, and keeps dropped candidates on record with the reasons.
Frequently asked questions
Is "non-etching" on a cleaner label a measured limit?
No. No published numeric threshold defines a non-etching aluminum cleaner, and Henkel describes even its low-etch cleaner as changing with temperature and concentration (Henkel product page, 2026). Ask the supplier for weight loss on your alloy at a stated temperature, concentration and time, then confirm it with your own coupons.
Can a non-etching cleaner remove light oxide as well as oil?
Some can. Henkel describes BONDERITE C-AK 212 as designed to remove oils and light oxide films from aluminum and its alloys (Henkel product page, 2026). Heavy oxide, scale or a specification that calls for deoxidizing still needs a separate deoxidizer step.
Is a water-break-free surface enough to approve a new aluminum cleaner?
No. ASTM F22-21 is a go or no-go check for hydrophobic films and is not quantitative (ASTM F22-21, 2021). The test says nothing about etch, smut or silicate residue. Pair it with weight loss, a wipe test and a downstream adhesion or coating test.