Lubinpla

Why stainless steel parts discolor after passivation

Summary

Stainless steel that discolors after passivation usually points to poor precleaning, a contaminated or overrun bath, a grade the bath does not suit, or leftover iron or acid. This applies to nitric and citric immersion treatments of machined or fabricated parts. A correct result looks unchanged from the bare metal.

  • Carpenter Technology advises rinse and bath water with less than about 50 ppm chlorides, while noting that some processes tolerate up to several hundred ppm (Carpenter Technology, 2003).

  • Free-machining Types 303, 416 and 430F and high-carbon Types 410, 420 and 440 may etch in 20% to 40% nitric acid; 20% nitric acid with 4% to 6% sodium dichromate avoids it (AISI and Nickel Institute, 2020).

  • In laboratory tests, citric acid passivation was more prone to flash attack than nitric acid, driven by excessive bath temperature, excessive immersion time and bath contamination (Carpenter Technology, 2003).

  • NASA PRC-5002G allows a slight discoloration only if the surface passes the water break free test, and rejects etching, pitting or frosting (NASA JSC, 2021).

This guide covers color changes that appear during or right after nitric or citric immersion passivation. It does not cover weld heat tint that was on the part before the bath, electropolished parts, or rust that develops months later in service, which have different causes and checks.

What does discoloration after passivation look like on stainless steel parts?

On stainless steel parts, discoloration after passivation shows up as a gray to black etched surface, dull or frosted patches, blotches where oil sat, a line at the liquid level, or brown rust spots after the first rinse or humidity exposure. A good result shows none of these, because the passive film is invisible: Carpenter Technology describes it as about 0.0000001 inch thick and acquired from air on any clean surface (Carpenter Technology, 2003).

Read the pattern before the color. A uniform dark, heavily etched surface over the whole part is the classic "flash attack" that Carpenter Technology ties to a contaminated passivating solution (Carpenter Technology, 2003). Patchy dull areas point to the surface, not the bath. Etching only above the liquid level appears on parts that were partially immersed (AISI and Nickel Institute, 2020). Rust bloom in crevices or on blasted faces points to iron that the treatment did not remove.

Acceptance rules are strict. ASTM A967/A967M-25 is the active specification for chemical passivation treatments and lists alternative tests, among them water immersion, high humidity, salt spray, copper sulfate and potassium ferricyanide-nitric acid tests (ASTM A967/A967M-25, 2025). Looking is not enough: visual inspection detects gross contamination, scale, rust and particulates but may not reveal thin films of oil or residual chemical films (ASTM A380/A380M-25, 2025).

NASA's process specification PRC-5002G requires passivated parts to show no etching, pitting or frosting, and allows only a slight discoloration if the surface passes the water break free test (NASA JSC, 2021). On a clean surface rinse water sheets evenly; on an oily one it beads.

What are the most likely causes of discoloration after passivation?

The likely causes of discoloration after passivation fall into five groups: poor precleaning, a contaminated or out-of-control bath, a bath that does not suit the grade or heat-treat state, iron left in the surface, and acid trapped by poor rinsing.

Poor precleaning

Oil and coolant left on parts react with the acid and form gas bubbles that cling to the surface and interfere with passivation (Carpenter Technology, 2003). Machining oil carried into the tank on the parts, called drag-in, also builds organic contamination in the bath, which can lead to flash attack or etching (Troske, 2019).

Contaminated, chloride-laden or overrun bath

Contamination of the passivating solution, sometimes with high levels of chlorides, can cause flash attack: a heavily etched or darkened surface (Carpenter Technology, 2003). Out-of-control temperature and aged baths add to the risk.

Grade or heat-treat state the bath does not suit

Free-machining and high-carbon straight-chromium grades may etch in plain 20% to 40% nitric acid (AISI and Nickel Institute, 2020). Carburized, nitrided or improperly hardened parts can be attacked in the tank (Carpenter Technology, 2003).

Free or embedded iron left in the surface

Nitric acid removes iron lying in the surface but does not remove the rust (AISI and Nickel Institute, 2020).

Trapped acid and rinse residue

Acid trapped where sulfides dissolved can attack the surface unless it is neutralized (Carpenter Technology, 2003).

How do you tell flash attack from embedded iron or sulfide staining after passivation?

Three things separate flash attack, embedded iron and sulfide staining: where the mark sits, whether a control coupon run in the same bath is also attacked, and whether the mark turns to rust in a water or humidity test. A control coupon is a clean piece of a resistant grade passivated alongside the parts. Work through the checks below before changing the bath or the process. Record each result against the part numbers, bath batch and time it applies to, because one discolored load can carry two causes at once.

The table shows which cause group each observation points to and what confirms or rules it out.

Check

What you see

Points to

Color and pattern over the whole part

Uniform gray to black, heavily etched or darkened surface

Flash attack from a contaminated or chloride-laden bath (Carpenter Technology, 2003)

Control sample run in the same bath

Control sample is attacked too

Bath problem; change the bath (Carpenter Technology, 2003)

Where the stain sits

Blotches or dull patches where oil or coolant stayed; water beads instead of sheeting

Poor precleaning; water break test fails (NASA JSC, 2021)

Grade and heat-treat state

303, 416, 430F, 410, 420 or 440 etched while 304 in the same bath is clean

Bath too weak for the grade (AISI and Nickel Institute, 2020)

Machined cross-sections of free-machining grades

Dark dots or pits along the rolling direction

Sulfides dissolved, possible trapped acid (Carpenter Technology, 2003)

Liquid line on partly immersed parts

Etched band above the bath level

Partial immersion (AISI and Nickel Institute, 2020)

Water or humidity exposure after re-cleaning

Rust spots, ferroxyl test turns blue

Free or embedded iron not removed (Euro Inox, 2007)

Read the control sample row first. If a clean coupon of a resistant grade is attacked in the same bath, the bath is the cause, and no change to precleaning or part handling will fix it. If the coupon stays bright while parts of one grade darken, the bath is not the whole answer and the grade, heat-treat state or surface condition comes next.

Recording which cause each check ruled out, and on which parts, is the discipline described in avoiding confirmation bias in a root cause investigation.

Why do 303, 416 and 440C parts darken after passivation?

303, 416 and 440C parts darken after passivation because sulfur or carbon makes them less resistant than the 300-series grades, so a plain nitric bath that suits 304 can etch them. The free-machining Types 416, 430F and 303 and the high-carbon Types 410, 420 and 440 may show etching in 20% to 40% nitric acid, and hot nitric solutions may etch or dull them further (AISI and Nickel Institute, 2020).

In 303 and 416 the problem is sulfur. Sulfides are added for machinability, and a typical nitric bath removes them partially or totally. That leaves microscopic discontinuities, and acid trapped in them can attack the part unless it is neutralized (Carpenter Technology, 2003). Carpenter Technology's alkaline-acid-alkaline process uses 5% sodium hydroxide at 71 to 82 °C (160 to 180 °F) for 30 minutes before and after a dichromate-inhibited nitric bath to neutralize that acid (Carpenter Technology, 2003).

Sodium dichromate is a hexavalent chromium compound (OSHA, 2009) that needs REACH authorisation in the EU (EU REACH Annex XIV, consolidated 2026) and falls under OSHA 29 CFR 1910.1026 in the US (29 CFR 1910.1026, as accessed 29 October 2026), so the alkaline-acid-alkaline steps and any bath sampling follow the SDS and those rules.

In 440C the problem is carbon and heat treatment. High-carbon, high-chromium martensitic grades must be hardened to become corrosion resistant, and attack can occur in the passivating bath if parts are improperly heat treated (Carpenter Technology, 2003). Straight-chromium grades may also discolor in nitric acid from mild stress or foreign material, most often the free-machining grades; adding 2% copper sulphate crystals by weight to the nitric acid eliminates that condition (AISI and Nickel Institute, 2020). Which bath suits each grade family is set out in passivation treatment by stainless steel grade.

How do you check a passivation bath that is discoloring parts?

To check a bath that is discoloring parts, run a control sample, titrate the acid, confirm the temperature, and estimate chloride and oil contamination. Carpenter Technology recommends a control sample to test the bath's effectiveness: if the sample is attacked, it is time to change the bath (Carpenter Technology, 2003).

Next, measure acid strength. Carpenter Technology publishes a simple titration for nitric baths: 1.0 ml of bath in water, titrated with 0.5N sodium hydroxide to a phenolphthalein end point, where ml of titrant times 3.24 gives the volume percent of nitric acid (Carpenter Technology, 2003). Baths with sodium dichromate are titrated to pH 7.0 with a pH meter instead (Carpenter Technology, 2003). Sampling and titration handle the bath acid, so both follow the bath chemicals' SDS (29 CFR 1910.1200, as accessed 23 October 2026). NASA PRC-5002G requires weekly analysis of nitric acid and dichromate concentration and a temperature check before each use (NASA JSC, 2021).

The third check is contamination. Carpenter Technology advises water with less than about 50 ppm chlorides, though some processes tolerate several hundred ppm (Carpenter Technology, 2003). For one nitric process type on listed alloys, NASA PRC-5002G requires a monthly test that chloride stays below 1000 ppm (NASA JSC, 2021). Organic buildup from oily parts also leads to flash attack, so regular analysis and maintenance of the chemistry is required (Troske, 2019). Citric baths need the same control: excessive temperature, excessive time and contamination all drove flash attack in laboratory tests (Carpenter Technology, 2003).

How do you remove discoloration and repassivate stainless steel parts?

Remove discoloration from stainless steel parts by fixing the cause first, then re-cleaning, removing the damaged or contaminated layer, repassivating in a bath that suits the grade, and retesting. Repassivating in the bath that caused flash attack repeats the damage.

Steps by cause:

  1. Oil and coolant residue: degrease with an alkaline, solvent or detergent cleaner and confirm with the water-break test before any acid (Avery, 2011).

  2. Embedded iron from blasting or tooling: pickle the surfaces thoroughly, since that is the way to remove embedded iron particles (AISI and Nickel Institute, 2020).

  3. Grade-sensitive etching: use the inhibited or higher-oxidizing treatment, or the 2% copper sulphate addition where the specification allows it; neutralize after the acid for free-machining grades (Carpenter Technology, 2003; AISI and Nickel Institute, 2020).

  4. Heavy flash attack: an etched surface is lost metal. ASTM A967/A967M-25 rejects parts that show etching, pitting or frosting on visual inspection (ASTM A967/A967M-25, 2025), so repassivation alone cannot save them.

Every acid, caustic and dichromate step follows the product SDS, which US OSHA 29 CFR 1910.1200 requires to be readily accessible to employees during each work shift (29 CFR 1910.1200, as accessed 23 October 2026).

Retest with the method the order names. Carpenter Technology notes that the copper sulfate test likely gives false positives on martensitic and lower-chromium ferritic 400-series grades, and evaluates 400-series precipitation-hardening and free-machining grades in a humidity cabinet at 100% humidity and 35 °C (95 °F) for 24 hours (Carpenter Technology, 2003).

When should you call a finishing specialist about passivation discoloration?

Call a finishing specialist about passivation discoloration when a control sample stays clean but parts still discolor, when the grade or heat-treat state is uncertain, or when parts already show etching that the specification rejects. Those cases need metallography or surface analysis, not another bath change.

Three situations call for help. The first is repeated failure on one grade after the bath is confirmed good, which points to the material: carburized or nitrided surfaces have lowered corrosion resistance and can be attacked in the passivating tank (Carpenter Technology, 2003). The second is a dispute over test results, because a test that is too severe fails good material and one that is too lenient passes bad parts (Carpenter Technology, 2003). The third is rust that keeps returning after repassivation, which suggests embedded iron that only pickling or mechanical removal will clear.

Bring the evidence: the grade and heat lot, the heat-treat record, bath titration and temperature logs, the control sample result, photographs of the pattern, and the test method and result. Lubinpla, an applied AI company that structures technical reasoning in specialty chemicals, works such a case from your own records: it sets hypotheses across the whole cause space first, then records each ruled-out cause with the scope of its exclusion. With that record, a specialist can start from the causes still open instead of retesting the ones already excluded.

Frequently asked questions

Is a slight color change after passivation acceptable?

A slight color change can be acceptable under some specifications but not others. NASA PRC-5002G allows a slight discoloration only if the surface passes the water break free test, while etching, pitting or frosting are rejected (NASA JSC, 2021). The purchase order and the specification it names decide.

Can citric acid passivation cause flash attack?

Yes, citric passivation can cause flash attack. Carpenter Technology reports that citric procedures were more prone to flash attack than nitric procedures in laboratory tests, driven by excessive bath temperature, excessive immersion time and bath contamination (Carpenter Technology, 2003).

Why do passivated parts rust after a water test?

Passivated parts rust in that test when free or embedded iron was not removed. Nitric acid removes iron lying in the surface but does not remove existing rust (AISI and Nickel Institute, 2020), and embedded iron from carbon steel shot or grit needs thorough pickling (AISI and Nickel Institute, 2020).

Does the ferroxyl test suit every part?

No, the ferroxyl test does not suit every part. It detects free iron or iron oxide (Euro Inox, 2007), but it is described as overly sensitive and not usable for food applications because the reagent contains cyanide (Avery, 2011).

Related posts