NSF H1 vs HT1 vs 3H: Choosing a Registration for a Food Plant
Summary
NSF H1 covers lubricants that food may touch incidentally, HT1 covers heat transfer fluids in that same zone, and 3H covers release agents that touch food directly. Pick the code by what the product does at each point and whether food can reach it, as your HACCP plan records. Where contact is impossible, H2 lubricants are acceptable.
21 CFR 178.3570 limits mineral oil from an incidental-contact lubricant to an addition to food not exceeding 10 parts per million (eCFR, 2026).
White mineral oil used as a release agent and lubricant in bakery products must not exceed 0.15% of the bakery products (21 CFR 172.878, eCFR, 2026).
The NSF White Book lists H1, H2, H3, HT1, HT2 and 3H as separate category codes, so one product can hold one code and not another (NSF White Book, 2026).
ISO 21469:2006 is Edition 1, was last confirmed in 2020, and a systematic review that closed on 3 September 2025 shows no decision yet (ISO, 2026).
This comparison covers the NSF Nonfood Compounds Registration Program and the US FDA rules it is based on. It does not replace your HACCP plan, customer specifications or food contact rules outside the United States, and it does not cover cleaners, sanitizers or the H3 and HT2 codes in detail.
How do NSF H1, HT1 and 3H registrations differ?
NSF H1, HT1 and 3H split on two things: the product class, and how close the product comes to food. H1 is for lubricants that may touch food incidentally, meaning contact is possible but not intended. HT1 covers heat transfer fluids with the same incidental exposure, and 3H covers release agents applied to surfaces that food touches.
In the NSF White Book each code is a separate listing, alongside H2 lubricants with no food contact, H3 soluble oils and HT2 heat transfer fluids with no food contact (NSF White Book, 2026). NSF grants a code for the use it reviewed. The same base oil can therefore sit in different categories, depending on whether it lubricates, moves heat or keeps food from sticking.
The table below shows which code a product needs, based on what the product is and where it sits.
NSF category | Product class and contact level | Where it may be used in the plant | FDA basis (21 CFR section) |
|---|---|---|---|
H1 | Lubricant, incidental food contact possible | Machine parts where the lubricated part may be exposed to food; antirust film; release agent on gaskets or seals of tank closures (21 CFR 178.3570(b), eCFR, 2026) | 178.3570 |
H2 | Lubricant, no possibility of food contact | Equipment and machine parts where neither lubricant nor lubricated part can contact edible products (NSF certificate 174276, 2026) | None named on the NSF certificate |
HT1 | Heat transfer fluid, incidental food contact possible | Heating and cooling circuits where incidental contact is possible (NSF White Book, 2026) | 178.3570, as one HT1 fluid maker states for its product (Duratherm, 2026) |
3H | Release agent, direct contact with food surfaces | Grills, ovens, loaf pans, boning benches and chopping boards in contact with meat and poultry, on one 3H certificate (NSF certificate 174175, 2026) | 172.878 per-use limits when the agent is white mineral oil; ask the supplier for the section its product was reviewed under |
HT1 is the row buyers miss most. A heat transfer fluid is not a lubricant, so an H1 code alone does not show that anyone reviewed it as a heat transfer fluid.
Where in a food plant does each NSF registration apply?
Match each registration to the product's function and its distance from food. H1 goes on lubrication points above or near exposed food. HT1 goes in heating and cooling circuits whose fluid could reach product through a leak. 3H goes on surfaces that food touches, and H2 belongs only where contact is impossible. The plant's HACCP team decides which points fall in which zone; ELGI calls the HACCP assessment "the ultimate guide" to where H1 lubricants are needed (Nye Lubricants, 2024).
One practical way to map a plant: walk the line once and give every lubrication point, circuit and release surface a single code.
Conveyor chains, bearings, gearboxes and slides over open product: H1.
Thermal fluid circuits that heat or cool kettles, ovens or chillers next to product: HT1.
Baking pans, grills, chopping boards and boning benches: 3H.
Machines in a separate room with no product, packaging or food contact parts: H2 is acceptable.
ISO 21469:2006 confirms that heat transfer is one route to incidental contact: its scope covers lubricants that "can come into incidental contact (e.g. through heat transfer, load transmission, lubrication or the corrosion protection of machinery) with products and packaging" (ISO, 2026). Even so, ELGI recommends H1 lubricants in all feasible applications, including below the production line, to reduce contamination risk (Nye Lubricants, 2024).
When is an H1 lubricant registration enough?
H1 is enough when the product lubricates a machine part, protects equipment from rust, or releases gaskets or seals of tank closures, in locations where the lubricated part may be exposed to food. 21 CFR 178.3570 names these three uses, and the rule requires that "the amount used is the minimum required to accomplish the desired technical effect on the equipment" (eCFR, 2026).
The registration also limits the formula. The lubricant must be prepared from substances generally recognized as safe, substances with a prior sanction or approval, or substances listed in the rule, and each listed substance carries its own limit. For mineral oil, the addition to food must not exceed 10 parts per million (21 CFR 178.3570, eCFR, 2026).
Antirust use adds a cleaning step. If an H1 product is used as an antirust film, NSF certificates require it to be removed by washing or wiping so that the surface is effectively free of any substance that could transfer to food (NSF certificate 146621, 2025).
H1 is not enough in two cases: a fluid whose job is heat transfer, which has its own HT1 code, and a release agent that touches food directly, which falls under 3H. ELGI makes the reverse point: a product that lubricates a bearing, chain or slide is covered by H1, and 3H products designed as equipment lubricants usually carry H1 registration too (Nye Lubricants, 2024).
When do heat transfer fluids need HT1 and release agents need 3H?
A heat transfer fluid needs HT1 when it runs in a circuit where incidental contact with food is possible. A release agent needs 3H when it goes on surfaces that food touches, to keep food from sticking during processing. In both cases function decides, not the base oil: a fluid that moves heat is judged as a heat transfer fluid, and an agent that keeps food from sticking is judged as a release agent.
For HT1, check the fluid's operating range as well as the code. Duratherm, for example, describes its 450-FG fluid as NSF registered as HT1, meeting 21 CFR 178.3570, with a maximum operating temperature of 232 °C (Duratherm, 2026). Run a fluid above its rated range and it is outside what its maker documented, whatever its registration.
For 3H, the limits sit in the FDA food additive rules, not in a lubricant rule. ELGI notes that 21 CFR 172.878 specifies the limits for each application of a 3H product, so a 3H code does not allow unlimited use (Nye Lubricants, 2024). For white mineral oil used as a release agent and lubricant in bakery products, the limit is 0.15% of the bakery products (21 CFR 172.878, eCFR, 2026). Ask the supplier which use, and which 21 CFR section, its 3H product was reviewed under, and match that to your process.
How do you check that an NSF registration is current?
To check that a registration is current, match the product label, the NSF Certificate of Registration and the NSF White Book listing. NSF certificates state that registration "is current when the NSF Registration Mark and Category Code appear on the product label" that NSF reviewed and the registered product name is in the NSF White Book (NSF certificate 146621, 2025).
Run this check for each product at receipt, and again at each audit cycle:
Read the label. It should show the NSF Registration Mark and the category code you need: H1, HT1 or 3H, not H2.
Read the certificate. Note the registration number, the exact registered product name, the company and the category code.
Look the product up in the White Book. Search by company name, product name or registration number and select the category you need (NSF White Book, 2026).
Compare names. The registered product name must match the product delivered, not a family name or a similar grade.
Record the result. Save the date checked, the registration number and the name of the person who checked, next to the certificate.
Because a product can hold more than one code, confirm that the listing and the label show the code that matches your use, not just any food-grade code.
Why is a supplier certificate not proof of NSF registration?
A supplier certificate is a dated letter: it shows that registration was granted on its issue date. NSF ties current registration to two other things: the reviewed label carrying the mark and category code, and the registered product name appearing in the NSF White Book (NSF certificate 146621, 2025). The certificate does not show that the product is still listed, that your label is the reviewed one, or that the name matches the delivery.
Audits turn up three gaps. The certificate names a different product or grade from the one in the drum. It carries an H1 code while the product works as a heat transfer fluid or a release agent. Or the product name no longer returns a result in the White Book. Any one of them leaves the plant unable to show the registration it relies on.
Registration also does not certify how a lubricant was made. ISO 21469:2006 specifies hygiene requirements for the formulation, manufacture, use and handling of incidental-contact lubricants and is listed as its own category in the White Book (ISO, 2026; NSF White Book, 2026).
To keep registration letters next to the related files at a distributor, see how to organize TDS, SDS and CoA files from many suppliers. Lubinpla lets a team tag an NSF registration letter as a certificate in its Dataroom and share that proof with a food customer; checking the White Book stays a person's job.
Frequently asked questions
Does the FDA approve H1, HT1 or 3H products?
No. The FDA does not approve or register lubricants. ELGI explains that H1 ingredients comply with 21 CFR 178.3570 (Nye Lubricants, 2024), and NSF bases its registration on an ingredient, labeling and appropriate-use review against FDA 21 CFR (NSF certificate 146621, 2025). What a food plant can check is the NSF code.
Can one product hold H1 and 3H at the same time?
Yes. A product can be registered in more than one category, and each code has its own White Book category. ELGI notes that 3H products designed as equipment lubricants usually carry H1 registration too (Nye Lubricants, 2024). Confirm the code that matches how you use the product.
Is an ISO 21469 certificate a replacement for NSF H1?
No. ISO 21469:2006 covers hygiene in the formulation, manufacture, use and handling of incidental-contact lubricants, while H1 covers the ingredient and label review against 21 CFR (ISO, 2026; NSF certificate 146621, 2025). The White Book lists ISO 21469 as a separate category, so check each claim against its own listing.
Where do the details for H1 grease sit?
The formula limits, label review and audit questions specific to grease are in what NSF H1 registration requires for food grade grease. This article stays with choosing a category for each product class in the plant.