Lubinpla

TDS and SDS flash points that do not match: which one to trust

Summary

A TDS and SDS flash point mismatch usually comes from different test methods, a typical value set against a classification value, or documents revised at different times. For hazard classification under US OSHA and EU CLP, the SDS closed cup value counts. If none of these causes explains the gap, it is an error to raise with the supplier.

  • US OSHA sorts flammable liquids into four categories with flash point breaks at 23 °C, 60 °C and 93 °C; categories 1 and 2 both sit below 23 °C and split at an initial boiling point of 35 °C (OSHA 29 CFR 1910.1200 App. B, 2024).

  • EU CLP has three flammable liquid categories up to a flash point of 60 °C, and its flash point determination must use a closed cup method (EU CLP Annex I 2.6, 2008).

  • ASTM D92-24, the Cleveland open cup method, applies to petroleum products with flash points above 79 °C and below 400 °C, except fuel oils (ASTM D92-24, 2024).

  • Under US OSHA, new significant hazard information must be added to the SDS within three months (OSHA 29 CFR 1910.1200, 2024).

This check applies when a technical data sheet (TDS) and a safety data sheet (SDS) cover the same product grade and each gives one flash point. It does not settle transport classification, which follows dangerous goods rules. Nor does it assign a hazard category near a break point; that call belongs to the SDS author.

What does a TDS and SDS flash point mismatch look like?

The mismatch shows up as two different temperatures for the same product grade, often with different method labels or no method at all. Illustrative example: a hydraulic oil TDS lists a flash point of 228 °C by ASTM D92, while section 9 of the SDS lists 210 °C, closed cup. Both numbers can be correct.

The two documents do different jobs. The SDS is a regulated document: under US OSHA, flash point is a required entry in SDS section 9, physical and chemical properties (OSHA 29 CFR 1910.1200 App. D, 2024), and under EU REACH the SDS must be compiled in accordance with Annex II, which uses the same section 9 heading (REACH Article 31). The TDS is a commercial document that describes typical performance. A lubrication engineer notes that some lubricant product or technical data sheets show differing test methods, open cup and closed cup (Williamson, Precision Lubrication).

That split is why the mismatch matters in two places. The SDS value drives hazard classification, storage and fire precautions. The TDS value is the one buyers copy into specifications and product comparisons.

Why do closed cup and open cup flash points give different values?

A closed cup holds the vapor above the liquid, while an open cup lets it escape. As a result, the closed cup method "usually results in a flash point that is a few degrees lower than in an open cup" (ILPI, SDS HyperGlossary). In an open cup tester, vapors are free to escape to the atmosphere and laboratory conditions can cause variations (Williamson, Precision Lubrication).

The two methods also cover different ranges. ASTM D92-24, the Cleveland open cup (COC) method, applies to petroleum products with flash points above 79 °C and below 400 °C, except fuel oils (ASTM D92-24, 2024). ASTM D93-26, the Pensky-Martens closed cup (PMCC) method, covers petroleum products from 40 °C to 370 °C (ASTM D93-26, 2026). The international counterparts are ISO 2592 for the Cleveland open cup and ISO 2719 for Pensky-Martens closed cup (Williamson, Precision Lubrication).

For classification, the rules point to closed cup results. US OSHA lists ASTM D56, D3278, D3828 and D93, or any method in 29 CFR 1910.106(a)(14) or GHS Revision 7, chapter 2.6, for flammable liquid classification (OSHA 29 CFR 1910.1200 App. B, 2024). EU CLP is explicit: "For flash point determination a closed-cup method shall be used." (EU CLP Annex I 2.6.4.1, 2008). So a lubricant TDS that reports COC and an SDS that reports PMCC are expected to differ, with the SDS value usually lower.

Is the TDS flash point a typical value and the SDS flash point a classification value?

Usually, yes. The TDS gives a typical value, the SDS gives the value used for hazard classification, and the two are not built to match. One gear oil TDS revised in July 2026 lists a typical flash point of 224.0 °C and a minimum of 200.0 °C, and states "Values are typical and may vary by lot." (Alliance Chemical, 2026).

On the SDS, flash point serves classification. US OSHA uses flash point breaks at 23 °C, 60 °C and 93 °C to place a liquid in one of four categories (OSHA 29 CFR 1910.1200 App. B, 2024); EU CLP uses three categories up to 60 °C (EU CLP Annex I 2.6.2, 2008). In both, categories 1 and 2 also split at an initial boiling point of 35 °C (OSHA 29 CFR 1910.1200 App. B, 2024; EU CLP Annex I 2.6.2, 2008).

The SDS value need not come from a test on the product at all. Under EU CLP, flash point data "can be determined by testing, found in literature or calculated" (EU CLP Annex I 2.6.4.1, 2008), and a mixture with a defined composition may rely on a calculated flash point if it is at least 5 °C above the relevant criterion and further conditions are met (EU CLP Annex I 2.6.4.2, 2008).

So a gap between a typical TDS value and a calculated or conservative SDS value is normal. It matters most when the two values sit on opposite sides of a category break.

Can a revision date gap between the TDS and SDS explain a different flash point?

A revision date gap can explain a different flash point when the product was reformulated or retested and only one document was updated. The SDS carries fixed revision duties. Under US OSHA, an SDS shows its date of preparation or last change in section 16 (OSHA 29 CFR 1910.1200 App. D, 2024), and new significant information on hazards must be added within three months (OSHA 29 CFR 1910.1200, 2024). Under EU REACH, suppliers must update the SDS without delay when new hazard information becomes available, identify the new version as "Revision: (date)" and send it to recipients supplied within the preceding 12 months (REACH Article 31, paragraph 9, 2006).

None of these rules applies to the TDS, which is a commercial document. Compare the revision date printed on each document, and ask whether the formulation, base stock or production site changed between those dates.

Distributors see this often, because they receive the same product documents from many suppliers. A filing method that keeps the current TDS and SDS of each grade side by side, as described in how a distributor should organize TDS, SDS and CoA files, makes a date gap visible before a customer finds it.

How can you tell TDS and SDS flash point mismatch causes apart?

Check four things in order: the method named on each document, the value type, the revision dates, and the direction and size of the gap. Work down the rows from the top; the first row that fits is usually the cause. The table below shows which cause each finding points to.

Check

What you see

Points to

Method on each document

TDS: ASTM D92 or ISO 2592 (open cup); SDS: ASTM D93, ISO 2719 or another closed cup method

Method difference; SDS usually lower (ILPI, SDS HyperGlossary)

Method on each document

Same method named on both, values differ

Value type, revision gap or error

Value wording

TDS says "typical" or "minimum"; SDS gives one value or a calculated value

Value type difference

Revision dates

One document revised after a reformulation, the other not

Outdated document

Direction of the gap

Closed cup value higher than the open cup value for the same grade

Unexpected; ask the supplier

Category break

Values fall on opposite sides of 23 °C, 60 °C or 93 °C (OSHA 29 CFR 1910.1200 App. B, 2024)

Resolve before use or sale

Product identity

Different grade code, viscosity grade or production site

Not the same product

In practice the first row comes up most: a lubricant TDS with an ASTM D92 open cup value next to an SDS with a closed cup value, where a lower SDS figure is expected. A closed cup figure above the open cup figure for the same grade runs against the usual direction. Treat that as a question for the supplier, not as a method effect. If the methods and value types match and the dates are current, what remains is an error in one of the two documents, and the supplier should correct it.

Why do published flash point sources disagree on the open and closed cup gap?

The sources describe different liquids and serve different purposes. The ILPI SDS reference says a closed cup reading is usually "a few degrees lower" than an open cup reading (ILPI, SDS HyperGlossary). A Maritime University of Szczecin lubricant laboratory manual, by contrast, states that the method must always be given with the result "because the correlations between the two methods are not known" (Krupowies and Wiznerowicz, Maritime University of Szczecin).

The difference likely comes from the volatile fraction, meaning any light solvent or fuel in the oil. ASTM D92-24 says ASTM D93 should be used when it is desired to detect small but significant concentrations of lower flash point substances that may escape detection by the open cup method (ASTM D92-24, 2024). A clean, narrow-cut oil may show a small gap. An oil with a light solvent or fuel fraction may show a larger one, because the open cup loses those vapors.

The Szczecin manual adds a limit: the open cup must not be used to assess the operational suitability of used marine oils, only fresh oils (Krupowies and Wiznerowicz, Maritime University of Szczecin).

Both sources lead to the same practical rule: there is no fixed conversion between open cup and closed cup flash points. Do not add or subtract a standard offset to make a TDS value match an SDS value. Quote each value with its method.

What should you ask the supplier about a flash point mismatch?

Send the supplier five specific questions, with both documents attached and their revision dates named.

  1. Which test method and standard produced each value: ASTM D92, ASTM D93, ISO 2592, ISO 2719 or another?

  2. Is the TDS value typical, a minimum, or a single batch result?

  3. Was the SDS flash point measured on this product, taken from literature, or calculated, as EU CLP allows (EU CLP Annex I 2.6.4.1, 2008)?

  4. Did the formulation, base stock or production site change between the two revision dates?

  5. Which value does the supplier use for hazard classification, and does it change the category on either side of 23 °C, 60 °C or 93 °C (OSHA 29 CFR 1910.1200 App. B, 2024)?

Some cases need a fire safety or regulatory specialist, not only the supplier: when the two values straddle a category break, when a used product shows an abnormally low flash point, or when storage rules for your site depend on the figure. ASTM D92-24 notes that an abnormally low flash point on engine oil can indicate gasoline contamination (ASTM D92-24, 2024).

In Lubinpla, the TDS and SDS can be filtered together in the Dataroom by their document type tags, and the main agent cites both documents as sources when it answers.

How do you answer a customer who asks which flash point to use?

Give the SDS value for safety decisions and the TDS value, labeled as typical, for product comparison, each with its method. Storage, handling and fire precautions follow the SDS: its section 9 value, its sections 5 and 7, and the local rule, such as the OSHA flammable liquids standard 29 CFR 1910.106 in the United States (ILPI, SDS HyperGlossary). The TDS value helps compare grades tested by the same method.

Write the method next to every number. ILPI puts it simply: "Because the two methods give different results, one must always list the testing method when listing the flash point." (ILPI, SDS HyperGlossary). A reply such as "210 °C closed cup per SDS section 9; 228 °C open cup, typical, per TDS" (illustrative values) answers the question and shows why both numbers exist.

If the supplier has not yet explained a gap that falls across a category break, say so in writing. Until the supplier confirms or corrects the SDS, use the lower of the two flash points for storage, handling and fire precautions. Do not average the two figures or convert one into the other: neither ASTM D92 nor ASTM D93 provides a conversion, and the sources above give no fixed offset.

Frequently asked questions

Is fire point the same as flash point?

No. Fire point is the temperature at which the flame becomes self-sustained, and it is usually a few degrees above the flash point (ILPI, SDS HyperGlossary). ASTM D92-24 measures both flash point and fire point in the same Cleveland open cup test.

Does a flash point above 93 °C mean a product cannot burn?

No. US OSHA defines a flammable liquid as one with a flash point of not more than 93 °C, so a higher value takes the liquid out of that hazard class (OSHA 29 CFR 1910.1200 App. B, 2024). ASTM D92-24 states that flash point is only one of a number of properties to consider in assessing overall flammability hazard.

Why does a used oil show a lower flash point than its new oil SDS?

A lower flash point in a used oil usually points to contamination with a lighter, more volatile liquid, not to an SDS error. ASTM D92-24 gives the example that an abnormally low flash point on engine oil can indicate gasoline contamination (ASTM D92-24, 2024).

Related posts