Boiler water additives for food-contact steam: 21 CFR 173.310
Summary
Under US FDA rule 21 CFR 173.310, a boiler water additive in food-contact steam may come only from the listed substances, within the listed limits (as of 2026-10-21). A boiler treatment qualifies when every ingredient matches a listed entry, each limit holds at the plant's dose, and the food plant uses no more additive or steam than the job needs.
Diethylaminoethanol is capped at 15 ppm in steam, and that steam may not contact milk or milk products (21 CFR 173.310, eCFR 2026).
Hydrazine is listed at zero in steam (21 CFR 173.310, eCFR 2026).
Acrylic acid/AMPS copolymer is capped at 20 ppm active in boiler feedwater (21 CFR 173.310, eCFR 2026).
The last amendment, effective 2023-03-24, changed only the office where incorporated references can be examined, not the substance list (FDA, 2023).
This answer covers the US federal rule and the state food codes that point to it. It does not cover steam that never contacts food, the EU, Canada or other jurisdictions, or a food plant's own customer specifications, which can be stricter than the federal list.
What and whom does 21 CFR 173.310 cover?
21 CFR 173.310 covers every boiler water additive used to make steam that will contact food in the United States. That binds both the treatment supplier, who formulates the product, and the food plant, which doses it. The section opens: "Boiler water additives may be safely used in the preparation of steam that will contact food, under the following conditions" (21 CFR 173.310, eCFR 2026).
The section sets three working conditions. Paragraph (a) limits the additive to the amount its functional purpose requires and the steam to the amount needed for the intended effect on the food. Paragraph (b) requires the compounds to be prepared from the substances listed in paragraphs (c) and (d), subject to their limitations. Paragraph (e) requires the label or labeling to bear the common or chemical name of each additive and adequate directions for use (21 CFR 173.310, eCFR 2026).
State food codes carry the same rule into retail and food service. Virginia states that chemicals used as boiler water additives "shall meet the requirements specified in 21 CFR 173.310" (12VAC5-421-3400, amended 2016), and Nevada uses similar wording (NAC 446.626, 2026).
As of 2026-10-21, the eCFR shows the section's most recent change on 2023-03-24, and the substance list matches the official edition revised as of 2025-04-01 (FDA, 2025).
Which boiler chemicals does 21 CFR 173.310 allow in food-contact steam?
21 CFR 173.310 allows the internal treatment chemicals that most low-pressure boiler programs use, provided each one is a listed substance and meets any limit written beside it. Paragraph (c) lists them; paragraph (d) adds the amines and two other substances that may be used alone or with them (21 CFR 173.310, eCFR 2026).
The paragraph (c) list covers alkalinity builders (sodium hydroxide, sodium carbonate, potassium carbonate, sodium silicate, sodium metasilicate), phosphates (sodium phosphate mono-, di- and tri-, sodium hexametaphosphate, sodium tripolyphosphate, tetrasodium pyrophosphate, potassium tripolyphosphate), oxygen scavengers (sodium sulfite neutral or alkaline, sodium metabisulfite, cobalt sulfate as catalyst), sludge conditioners (tannin including quebracho extract, lignosulfonates, sodium alginate, sodium carboxymethylcellulose) and chelants and dispersants (tetrasodium EDTA, HEDP and its sodium and potassium salts, sodium polyacrylate, sodium polymethacrylate) (21 CFR 173.310, eCFR 2026).
Several listed polymers carry dose limits measured in boiler feedwater. Acrylic acid/AMPS copolymer is capped at 20 ppm active, poly(acrylic acid-co-hypophosphite) sodium salt at 1.5 ppm, and polymaleic acid or its sodium salt at 1 ppm calculated as the acid (21 CFR 173.310, eCFR 2026). Some entries also limit the raw material itself, such as acrylamide-sodium acrylate resin with no more than 0.05 percent acrylamide monomer (21 CFR 173.310, eCFR 2026).
Match names with care. The list names sodium metabisulfite and sodium sulfite, but not sodium bisulfite by that name, so confirm how each scavenger appears on the SDS before you match it.
What are the amine limits in steam under 21 CFR 173.310?
21 CFR 173.310 caps the four listed amines in steam: cyclohexylamine and morpholine at 10 ppm, diethylaminoethanol at 15 ppm and octadecylamine at 3 ppm, and none of them may be in steam that contacts milk or milk products (21 CFR 173.310, eCFR 2026). Trisodium nitrilotriacetate is capped at 5 ppm in boiler feedwater and may not be used where steam contacts milk or milk products. Each amine carries its own limit and its milk exclusion. How neutralizing and filming amines compare is a separate question.
Each limit is measured at a set point, in the steam or in the feedwater, and a reply should say which one applies. The amine limits are steam concentrations, so they depend on the feed rate, the steam load and how the amine distributes between steam and condensate. The polymer and nitrilotriacetate limits are feedwater concentrations, which a dose calculation at the plant's feedwater flow can show. The sorbitan monostearate and polysorbate mixture used as an anticorrosive in steam distribution systems is capped at 15 mg/kg of each component in the steam (21 CFR 173.310, eCFR 2026).
A dairy plant may apply a stricter rule. 3-A Accepted Practice 609-03 for culinary steam, adopted 2004-11-21, states that "Boiler compounds containing cyclohexylamine, diethylaminoethanol, hydrazine, morpholine, octadecylamine, trisodium nitrilotriacetate are not permitted" (3-A SSI, 2004). So a condensate amine program that sits inside the federal ppm limits can still fail a customer who builds its culinary steam to 3-A 609-03.
Does 21 CFR 173.310 allow hydrazine, DEHA or carbohydrazide?
21 CFR 173.310 does not allow hydrazine in food-contact steam, and it does not list DEHA (diethylhydroxylamine) or carbohydrazide at all. Hydrazine appears in paragraph (d) with the limitation "Zero in steam" (21 CFR 173.310, eCFR 2026). Carbohydrazide and DEHA appear nowhere in paragraphs (c) or (d) of the current eCFR text, which is up to date as of 2026-10-21.
Paragraph (b) requires the compounds to be prepared from the listed substances. A volatile oxygen scavenger product built on DEHA or carbohydrazide therefore does not meet the conditions of this section for food-contact steam. This section does not say whether any other authorization covers such a product. That question belongs to the food plant's regulatory adviser.
The scavengers the list does name are sodium sulfite (neutral or alkaline), sodium metabisulfite and cobalt sulfate as a catalyst (21 CFR 173.310, eCFR 2026). All three are non-volatile: they protect the boiler and feedwater but not the condensate system. A plant that needs a volatile program for a high-pressure boiler can still supply food-contact steam from a separate sulfite-treated boiler or a clean steam generator. That split is an inference from the list, not a rule in the section.
The amendment history settles one doubt: the 2023 amendment to 21 CFR 173.310 left the substance list alone. It only changed the address in paragraph (f). In its own words, it "revises where the references are available for examination to be FDA's Dockets Management Staff" (FDA, 2023).
How do you check a boiler treatment's ingredients against the 21 CFR 173.310 list?
Check a boiler treatment against 21 CFR 173.310 one ingredient at a time: match each SDS ingredient to a listed entry, confirm any limit on the substance itself, then confirm each dose or steam limit at the plant's conditions. A product passes only when every ingredient passes, since paragraph (b) applies to all the compounds in it (21 CFR 173.310, eCFR 2026).
Start from the SDS composition and the supplier's full ingredient statement, because an SDS may not list every non-hazardous ingredient. Match by chemical name and, where the entry gives one, by CAS number, as for HEDP (CAS 2809-21-4) (21 CFR 173.310, eCFR 2026).
When a customer asks for the complete formula to run this check, decide first how much to disclose; what a supplier must disclose when a customer asks for the full formulation covers that step.
For each check, the table below gives the condition that applies, the evidence that answers it and who signs it off.
Ingredient check | 21 CFR 173.310 condition | Evidence to attach | Who decides |
|---|---|---|---|
Identity | Each ingredient is a substance in paragraph (c) or (d) (21 CFR 173.310, eCFR 2026) | SDS composition, supplier ingredient statement | Supplier |
Raw material limit | Example: acrylamide-sodium acrylate resin with no more than 0.05 percent acrylamide monomer (21 CFR 173.310, eCFR 2026) | Raw material specification or certificate of analysis | Supplier |
Feedwater limit | Example: acrylic acid/AMPS copolymer at no more than 20 ppm active (21 CFR 173.310, eCFR 2026) | Dose calculation at the plant's feedwater flow | Supplier proposes, food plant confirms |
Steam limit and milk exclusion | Example: morpholine at no more than 10 ppm in steam, no milk contact (21 CFR 173.310, eCFR 2026) | Steam or condensate test results, list of steam uses | Food plant |
Label | Common or chemical names and adequate directions for use | Product label and dosing instructions | Supplier |
The identity row decides most cases: one unlisted ingredient, such as a DEHA scavenger blended into a multifunctional product, fails the whole product.
Which part of the 21 CFR 173.310 decision belongs to the food plant customer?
The food plant customer decides whether its own steam use meets 21 CFR 173.310, because paragraph (a) ties compliance to how much additive and steam the plant uses for its food (21 CFR 173.310, eCFR 2026). A supplier can show that every ingredient is listed and that the recommended dose meets the feedwater limits, but it cannot see how the plant runs its boiler.
Three judgments stay with the plant. The first is where its steam goes: direct injection, open kettles, sterilizing product contact surfaces, or only indirect heating. The second is whether any steam contacts milk or milk products, which removes the four amines and nitrilotriacetate from the program (21 CFR 173.310, eCFR 2026). The third is which stricter standard the plant applies, such as 3-A 609-03, which also recommends "periodic analysis be made of condensate samples" taken at the final steam separating equipment (3-A SSI, 2004).
A supplier reply should therefore state each listed entry and limit as fact, mark the steam-side limits as conditions the plant verifies, and name the plant as the party that decides suitability. Date the reply's evidence, because the plant's auditor will ask which edition of the list it was checked against.
Lubinpla drafts this kind of technical inquiry reply from the supplier's own SDS, TDS and certificates, attaches the regulation and ingredient evidence to each item, and states that the customer decides suitability.
Frequently asked questions
Does 21 CFR 173.310 apply to steam that only heats food indirectly?
The section's opening sentence covers steam "that will contact food," so steam that only heats food through a heat exchanger wall falls outside its wording. A plant may still hold all its boilers to the list where steam lines and condensate can be cross-connected. The plant's food safety plan decides which boilers count as food-contact.
Is an older CFR printing of 21 CFR 173.310 still a valid reference?
An older printing, such as the 1996 text, predates amendments made in 1999, 2013 and 2023, according to the amendment history at the end of the current section (21 CFR 173.310, eCFR 2026). Cite the current eCFR text or the latest annual edition, and record the date you checked it.
Does the product label have to name the boiler water additives?
Yes. Paragraph (e) of 21 CFR 173.310 requires the label or labeling to bear the common or chemical name or names of the additives and adequate directions for use to ensure compliance with the section. A product sold for food-contact steam without those names leaves the food plant no way to run the ingredient check.
Does a state food code add limits beyond 21 CFR 173.310?
The state codes checked here, Virginia 12VAC5-421-3400 and Nevada NAC 446.626, point back to 21 CFR 173.310 and add no list of their own. Stricter limits can come from customer specifications or dairy practice such as 3-A 609-03, not from these state rules.