Switching a boiler to filming amines: risks and failure modes
Summary
Problems after a boiler switch to filming amines usually have one of three causes: loosened deposits, overfeed during start-up, or a residual tested in the wrong stream. All three show up in the first weeks of feed in industrial steam boilers. A slow start, total iron monitoring and a residual test at the right sample point catch them before damage.
Solenis advises starting filming amine feed at one-third of the final rate and raising it gradually, because rapid feed into a fouled system loosens deposits (Solenis, 2020).
IAPWS TGD11-19 recommends testing the filming amine residual daily at a minimum until a stable residual is reached in boiler feedwater (IAPWS, 2019).
Monitored parameters typically stabilize over 3-4 weeks as a minimum, and at least three months of total iron data are needed to compare with the baseline (IAPWS, 2019).
In the United States, 21 CFR 173.310 limits octadecylamine to not more than 3 ppm in steam that contacts food, excluding steam in contact with milk and milk products (eCFR, as of 2026-10-21).
This guide covers industrial steam boilers and condensate systems changing to a film forming amine or a film forming amine product. Non-amine film forming products, plants with condensate polishers and boilers already carrying heavy waterwall deposits need a separate assessment, and the regulatory limit quoted applies to steam that contacts food in the United States.
What usually goes wrong when a boiler switches to filming amines?
A switch to filming amines usually goes wrong in one of three ways. Deposits loosened by the amine travel through the steam and condensate system, the amine is overfed during start-up, or the residual is tested in a stream that cannot show it yet. Each problem has its own first sign, so name the problem before you change the feed rate.
Loosened deposits from the boiler and condensate lines
Filming amines adsorb strongly on metal oxide surfaces and can partially remove porous oxides and deposits. IAPWS TGD11-19 names this cleaning effect as the main reason to begin below the estimated final dosage (IAPWS, 2019). The usual signs are plugged strainers and steam traps and a rise in condensate iron.
Overfeed during start-up
Overfeed often starts as a reaction to a blank residual test: no amine shows, so someone raises the feed. IAPWS TGD11-19 says long overdosing raises metal oxide transport and forms sticky deposits in strainers, filters, steam traps and small pipes (IAPWS, 2019).
Testing in the wrong stream
Early in the switch, filming amine may not appear in condensate at all, because it adsorbs onto metal surfaces (IAPWS, 2019). Solenis advises testing the level in the steam rather than the condensate (Solenis, 2020). Reading a blank condensate test as underfeed leads straight to overfeed.
How can you tell filming amine switchover problems apart on site?
On site, the switchover problems separate on strainers and traps, total iron, deposit texture, conductivity against a lab sample, and the residual at each sample point, all readings most steam plants already take. Use the table below to decide which problem is under way before anyone changes the feed rate.
Check | What you see | Points to |
|---|---|---|
Condensate strainers and steam traps, first weeks | Plugging with loose oxide soon after first feed | Loosened deposits (Solenis, 2020) |
Total iron in condensate and feedwater | Rise in particulate iron during the initial period | Cleaning effect; reduce or stop feed if levels climb (IAPWS, 2019) |
Strainers, filters, traps and small pipes after weeks of feed | Sticky or gel-like deposits, clumps called "gunk" balls | Overfeed (IAPWS, 2019) |
Online conductivity against a lab grab sample | Online reading drifts away from the lab value | Probe coating by some film forming amine products (IAPWS, 2019) |
Cation conductivity in steam | Higher than before the switch | Breakdown products or released impurities; rule out a contaminant leak (IAPWS, 2019) |
Filming amine residual in condensate | Zero early in the switch | Normal adsorption demand, not proof of underfeed (IAPWS, 2019) |
Spool piece or corrosion coupon | Water wets the metal instead of beading | Film not yet formed, underfeed, or a rough oxide surface (IAPWS, 2019) |
Timing and deposit texture settle most disputes: loose oxide in strainers with an iron rise in the first weeks points to loosened deposits, while sticky or gel-like deposits after weeks of feed point to overfeed, often with rising iron. Run the quick checks, strainers and iron, before the lab checks for residual and conductivity.
Plugged strainers together with a zero residual in condensate are common early in the switch and point to loosened deposits plus normal adsorption demand (the amine is still coating the metal), not underfeed. Date each result so the trend stays visible.
What happens to existing deposits when filming amines are first fed into a boiler?
When filming amines are first fed into a boiler, existing deposits can loosen and travel, because the amine penetrates oxide layers and corrosion products in the return lines. Solenis warns that if filming amines are fed too rapidly into a fouled system, existing deposits slough off and may plug strainers and collect in low-flow areas (Solenis, 2020).
IAPWS TGD11-19 calls this a moderate cleaning effect: during the initial period of treatment, an increase of particulate iron oxides, and copper oxides where copper alloys are present, will be measured, and the effect is usually limited in duration (IAPWS, 2019). The guidance asks the operator to monitor total iron across the cycle, to reduce or stop the addition rate if corrosion products are elevated, and, where needed, to increase blowdown to keep iron within control guidelines (IAPWS, 2019).
The larger risk is heavy deposits on boiler heat transfer surfaces. IAPWS TGD11-19 states that film forming substances should not be used as a means of cleaning up heavy deposits in an operating boiler, because uncontrolled metal oxide transport is a major risk to boiler reliability (IAPWS, 2019). Cases presented to a users group in 2023 include a double-pressure HRSG with under-deposit corrosion failures after a film forming amine product was applied without a thorough up-front review (Dooley, 2023). In another HP evaporator, total deposit loading rose from 19 to 24 mg/cm2 in a 2018 assessment to 47 to 71 mg/cm2 in 2022, after a film forming product was added in 2020 (Dooley, 2023).
What are the signs of filming amine overfeed in a steam system?
Overfeed shows up as sticky or gel-like deposits in strainers, filters, steam traps and small-bore pipes, often with higher metal oxide transport. IAPWS TGD11-19 states that an overdosage of filming amine for a long period of time must be avoided, because it increases the risk of higher metal oxide transport and the formation of sticky deposits especially in strainers, filters, steam traps and small pipes (IAPWS, 2019). The same guidance reports that constant overdosing can form "gunk" balls, clumps of gel-like material that can block vessels or tubes (IAPWS, 2019). IAPWS gives the same warning for fossil and combined cycle power plants (IAPWS TGD8-16, 2019).
Overfeed has a chemical basis. In laboratory suspensions, low filming amine concentrations reduced magnetite deposition while high concentrations made the particles coagulate, and IAPWS calls the key to control keeping the free amine concentration constantly low (IAPWS, 2019). Free amine is amine still in the water, not bound to metal. A plant that raises feed because condensate shows no residual can reach this state without noticing.
Where steam contacts food in the United States, overfeed is also a compliance question: 21 CFR 173.310 allows octadecylamine at not more than 3 ppm in steam and excludes steam in contact with milk and milk products (eCFR, as of 2026-10-21).
If you see sticky deposits, reduce or stop the feed, as IAPWS TGD11-19 advises for elevated corrosion products, and test the residual daily until it is stable at a lower rate (IAPWS, 2019).
Why can conductivity readings change after switching a boiler to filming amines?
Conductivity readings can change for two reasons: the product's breakdown products raise cation conductivity, and some products coat conductivity probes. The amine itself has little effect: due to the low concentration used, its impact on pH and conductivity is negligible compared with alkalizing agents such as ammonia or neutralizing amines (IAPWS, 2019).
Three mechanisms explain most changes. First, film forming amine products degrade thermally into low molecular weight organic acids and carbon dioxide, which add to cation conductivity in steam and condensate; the products can also release impurities held in oxide layers and raise cation conductivity for a while (IAPWS, 2019). Second, in laboratory tests some products coated conductivity probes and caused drift in specific conductivity and calculated pH, while pH electrodes showed no negative influence (Betova et al., 2014). Third, a higher cation conductivity baseline can mask chloride or sulfate from a condenser leak (IAPWS, 2019).
Before acting on a drifting online reading, check it against a lab grab sample. Ask the supplier for the product's decomposition products and their effect on steam cation conductivity, which IAPWS TGD11-19 says the supplier should provide before a new application (IAPWS, 2019). IAPWS also notes that pH, conductivity or TOC measurement is not accurate enough to monitor filming amine dosing (IAPWS, 2019).
How do you test filming amine levels and film coverage after the switch?
Measure filming amine levels with a spectrophotometric residual test at every available sample point, and check film coverage by water beading on a spool piece or coupon. IAPWS TGD11-19 recommends the residual test daily at a minimum until a stable residual is achieved in boiler feedwater, with pH monitored continuously (IAPWS, 2019). The two common methods are methyl orange extraction and xanthene dye methods such as Rose Bengal (IAPWS, 2019).
Sampling decides whether the number means anything. Filming amine coats sample lines, so keep a constant flow on the extraction line. Store grab samples in PTFE with a little acetic acid and avoid cold storage; do not add detergent to extend storage, because detergents interfere with both colorimetric methods (IAPWS, 2019). Solenis advises testing the level in the steam rather than the condensate (Solenis, 2020), and IAPWS asks for control at all available sample points because distribution and adsorption differ around the system (IAPWS, 2019).
For film coverage, install a spool piece in the condensate return or use corrosion coupons; protected metal should bead water like a freshly waxed car (Solenis, 2020). A wet surface is not proof of failure: IAPWS notes that rough surfaces with porous iron oxide may not show hydrophobicity even when the amine is present (IAPWS, 2019).
When is keeping the current boiler amine program the better choice?
The current program is the better choice when the plant already meets its corrosion product targets and no change in operation creates a need that program cannot cover. IAPWS TGD11-19 says the first question should be why there is a need to change, and that a plant operating successfully within accepted guidance should have an operating or economic benefit before it changes (IAPWS, 2019). The typical reasons to switch are a shift to more starts and shutdowns, long layups, or high makeup alkalinity that limits neutralizing amine feed (Solenis, 2020; IAPWS, 2019).
Keep the current program, or postpone the switch, in four situations. No baseline exists: without total iron and cation conductivity data from before the switch, IAPWS says the plant cannot show that the change helped (IAPWS, 2019). Heavy deposits are known or suspected on heat transfer surfaces and no inspection or chemical clean is planned. The supplier does not disclose the product's composition, decomposition products and test method. The steam contacts food and the product's regulatory status is not documented.
The same weighing of options applies to any chemistry change, and our guide to the risks of moving a customer to a new formulation walks through it from the supplier's side.
When should you call a boiler water specialist about a filming amine switch?
Call a boiler water specialist before the first feed if no baseline exists or deposits are suspected, and during the switch if iron keeps rising or sticky deposits appear. At those points a wrong call costs boiler tubes rather than chemical.
Bring these records: total iron and conductivity data before and after the switch, the feed rate history with dates, strainer and trap findings, the residual test results by sample point, the product's safety data sheet (SDS) and composition statement, and any inspection photos of drums and tubes. IAPWS TGD11-19 lists the plant condition records worth keeping before a switch, from sludge in drums and deaerators to the time needed for start-up after shutdowns (IAPWS, 2019).
Ask three questions. Is the iron rise still the initial cleaning effect, or has it lasted beyond the period the supplier predicted? Do the deposits found in strainers contain organic material, which points to overfeed? Has cation conductivity risen beyond what the product's decomposition products explain?
Lubinpla's feasibility review sets out keeping and switching as separate scenarios, each with its early warning signs and the conditions for switching, in one cited document for your review.
Frequently asked questions
How long does a filming amine switchover take to settle?
IAPWS TGD11-19 says monitored parameters are typically stable after 3-4 weeks as a minimum, varying with the prior chemistry, materials and operating mode, and suggests at least three months of total iron data before comparing with the baseline (IAPWS, 2019).
Should the neutralizing amine feed continue after the switch?
Usually yes, at first. Solenis notes that most filming amines are fed together with neutralizing amines (Solenis, 2020). IAPWS says that if the new product contains an alkalizing amine, the previous alkalizing agent can be reduced or stopped while pH is monitored (IAPWS, 2019).
Who must supply the regulatory information for a filming amine product?
IAPWS TGD11-19 says the supplier should provide all information needed to ensure regulatory compliance, including food applications, chemical inventory listings and discharge (IAPWS, 2019). Ask for it in writing before the first delivery, and check each component against the rules where the plant operates.