Lubinpla

Replacements for Dicyclohexylamine (DCHA) in Metalworking Fluids

Summary

Choose a primary amino alcohol such as AMP where dicyclohexylamine supplied pH reserve, and a carboxylic acid amine salt where it supplied ferrous rust protection. If DCHA was also holding back microbes in the water-miscible coolant, plan a registered biocide and a bioresistance test as well, since an amine swap alone may not restore that effect.

  • TRGS 611 caps secondary amine impurities at 0.2 mass % of the water-miscible concentrate (TRGS 611, 2007).

  • TRGS 611 lists DCHA, CAS 101-83-7, as not a secondary amine in its sense because its nitrosamine is not a category 1 or 2 carcinogen (TRGS 611, 2007).

  • Dicyclohexylamine's conjugate acid has a pKa of 10.4 (PubChem, 2026).

  • In one synthetic fluid with 1000 ppm triazine biocide, the MEA and TEA version failed bacterial control after 4 weeks (STLE, 2013).

This answer covers water-miscible metalworking fluids: soluble oils, semi-synthetics and synthetics. It does not cover neat cutting oils, DCHA used as a vapor-phase or packaging rust preventive, or the biocide registration rules of a specific country, which need their own check.

What did DCHA do in a metalworking fluid?

Dicyclohexylamine (DCHA) did up to three jobs in a water-miscible metalworking fluid: it raised and held pH, it helped protect ferrous parts from rust, and in some fluids it suppressed microbes. DCHA is an amine base whose conjugate acid has a pKa of 10.4 (PubChem, 2026), so it neutralizes acid components in the concentrate and keeps the diluted fluid alkaline. A Metrohm application note on cooling lubricants that contain DCHA and methyldicyclohexylamine states that "Amines are added to the emulsion to keep the pH high" (Metrohm, AN-C-177). Researchers at North Carolina State University describe DCHA as used "to prevent corrosion of fabricated materials" and report increased use as a biocide in metalworking fluids, although it is not registered by the U.S. EPA for that purpose (Baynes et al., 2011).

A patent on boron-free inhibitors adds a caution: corrosion inhibition by DCHA and similar amines "is generally attributed merely to their basic nature" (US 9828566 B2, 2017). That caution shapes the replacement. If the rust protection in your fluid came mostly from pH, a primary amine that holds the same pH may be enough. If it came from a salt the amine formed with an acid in the package, you need a dedicated inhibitor. Before choosing anything, find out which of the three roles DCHA actually carried in your formulation, at what treat rate, and next to which acids and biocides.

Why are metalworking fluid makers moving away from DCHA?

Metalworking fluid makers are moving away from dicyclohexylamine (DCHA) mainly because customer specifications and hazard labels push against secondary amines, not because Germany's TRGS 611 names DCHA as banned. TRGS 611, in its May 2007 edition (the edition DGUV still cites in its guidance dated 26 March 2024), bars nitrosatable secondary amines as components of water-miscible concentrates. A nitrosatable amine is one that can form nitrosamines with nitrite. The rule then exempts DCHA by name, because DCHA's nitrosamine is not a category 1 or 2 carcinogen; the same rule notes that N-nitrosodicyclohexylamine, CAS 947-92-2, was classified as a category 3 mutagen (TRGS 611, 2007). Most summaries skip that exemption.

The pressure comes from buyers and labels instead. The STLE primer on amines notes the 0.2 % impurity limit and adds that "Some multinational users of MWFs have also requested that current or future generations of products not be formulated with secondary amines" (STLE, 2013). A patent on boron-free inhibitors says DCHA "faces a decline in acceptance due to it being a secondary amine" that can form nitrosamines with nitrite (US 9828566 B2, 2017). Hazard labels add pressure: in ECHA notifications summarized by PubChem, 98.6 % classify DCHA as H314, causing severe skin burns, and 98.3 % as H410, very toxic to aquatic life with long-lasting effects (PubChem, 2026). Treat the driver in your case as a customer specification or labeling decision, and confirm the current TRGS 611 text with BAuA before you quote it to a customer.

Which amines can replace DCHA in water-miscible coolant?

Primary amines and primary alkanolamines are the safest place to start, because TRGS 611 names them as the preferred replacements for nitrosatable secondary amines: their nitrosation does not lead to stable N-nitrosamines, and they also inhibit nitrosamine formation from secondary amines (TRGS 611, 2007, section 4.2). Common primary choices in metalworking fluids include monoethanolamine (MEA), monoisopropanolamine (MIPA) and 2-amino-2-methyl-1-propanol (AMP), which differ in neutralization and buffering efficiency (STLE, 2013).

Tertiary amines such as triethanolamine (TEA) are also used, but TRGS 611 calls for the highest practical purity where a tertiary amine still carries secondary amine impurities (TRGS 611, 2007). Amine choice also affects fluid life, the time before bacterial counts climb: in one synthetic fluid with 1000 ppm (at dilution) of a triazine biocide, the MEA and TEA version failed bacterial control after 4 weeks, while partial replacement with another performance amine held for 12 or more weeks (STLE, 2013).

Amine-free concentrates are a third route. TRGS 611 accepts them, but asks for close attention to pH stability and recommends nitrosamine inhibitors in use (TRGS 611, 2007, section 4.3). A replacement rarely matches DCHA one for one in basicity and oil solubility, so expect to change the treat rate and sometimes to combine two amines, as MEA and TEA have long been combined for neutralization and buffering (STLE, 2013). Ask each amine supplier for the secondary amine content on the certificate of analysis before the first bench batch.

How do you match a DCHA replacement to the role it played?

To match a dicyclohexylamine replacement to the role DCHA played, name that role first, screen the replacement class for it, then confirm the choice with the bench test that measures it. A swap that restores pH can still fail on rust or on fluid life, because each role has a different chemistry behind it. The table gives no treat rates, because they depend on the rest of the package.

For each DCHA role, the table below shows which replacement class to screen and which check proves it.

Role DCHA played

Replacement candidates

What to recheck

pH development and reserve (DCHA pKa 10.4, PubChem 2026)

Primary amino alcohol such as AMP or MIPA, often with TEA for reserve

Weekly pH; avoid a sustained drop of more than 0.5 pH units from fresh mix (TRGS 611, 2007)

Ferrous rust protection

Amine salts of C10 to C12 dicarboxylic acids, neutralized with MEA and TEA or with MIPA or AMP (ChemCeed, 2016)

Iron chip corrosion, ASTM D4627-22

Microbial suppression

Registered biocide; amine chosen for bioresistance

Bioresistance challenge, ASTM E2275-24, relative ranking only

Constraint on any replacement: secondary amine impurities

Primary amines; tertiary amines of high purity

Secondary amines at or below 0.2 mass % of concentrate (TRGS 611, 2007)

The row people miss most often is microbial suppression. If DCHA was holding back bacteria or fungi, an AMP swap can restore pH but not that effect, so the biocide package needs its own decision. The full method for this kind of swap, from role definition to trial, is in how to substitute a raw material in an existing formulation.

What performance is easiest to lose when DCHA is removed?

Ferrous rust protection and fluid life are the two properties most easily lost when dicyclohexylamine (DCHA) leaves a water-miscible metalworking fluid. Rust shows first where chips nest and drilled holes hold fluid, at the lean end of the dilution range where the fluid is most dilute. ASTM notes there is usually a relationship between iron chip results and rust on nested parts or in drilled holes containing chips (ASTM D4627-22). If DCHA's rust protection came mainly from basicity, a replacement with lower pH at use dilution is likely to show it first in the iron chip test.

Loss of fluid life takes longer to show. DCHA has been used as an unregistered biocide in metalworking fluids (Baynes et al., 2011), so removing it can shorten the time before bacterial counts climb. The STLE example, 4 weeks against 12 or more weeks with a different amine package, shows how large the effect of amine choice alone can be (STLE, 2013).

Three further properties can shift with any amine change: foam, cobalt leaching from carbide tools, and microbiological resistance, which STLE lists among the secondary characteristics amines affect (STLE, 2013). Hard water stability matters when the new rust package is a dicarboxylic acid salt; one supplier reports good hard water stability for a C10 to C12 diacid blend (ChemCeed, 2016), but confirm it in your own water. Run each of these against the DCHA version side by side, not against a specification limit alone.

Which tests should you repeat after replacing DCHA?

After replacing dicyclohexylamine (DCHA), repeat every test that measured a role DCHA carried, side by side with the original fluid at the same dilution and in the same water. Work through this checklist:

  1. pH at use dilution, then weekly over several weeks. TRGS 611 asks that a sustained drop of more than 0.5 pH units from the fresh mix be avoided (TRGS 611, 2007).

  2. Iron chip corrosion by ASTM D4627-22 at your lean and normal dilutions. ASTM warns that "conditions, metal types, etc. found in practice will not correlate quantitatively with these controlled laboratory conditions" (ASTM D4627-22).

  3. Bioresistance by the ASTM E2275-24 practice, with and without the planned biocide. ASTM states the results "should be used only to compare the relative performance of products or microbicide treatments included in a test series" (ASTM E2275-24).

  4. Secondary amine content of the new concentrate, at or below 0.2 mass % where TRGS 611 applies (TRGS 611, 2007).

  5. In use, nitrite weekly, with action above 20 mg/l (TRGS 611, 2007).

  6. Foam, hard water stability and, for carbide tooling, cobalt leaching.

Lubinpla's formulation design task follows the same order from your own TDS, SDS and test history: it defines the role the raw material played, screens replacement candidates for compatibility, process and safety, and returns a bench test plan as one cited document for your review.

Frequently asked questions

Do amine-free coolants avoid the DCHA question entirely?

Amine-free coolants avoid the amine choice but not the work behind it. TRGS 611 accepts amine-free water-miscible concentrates, yet asks users to watch pH stability closely and recommends nitrosamine inhibitors in case contaminants carry amines into the sump (TRGS 611, 2007). Rust and bioresistance tests still apply.

Does removing DCHA change the nitrite checks a shop must run?

No. Removing DCHA does not change the in-use monitoring under TRGS 611. Nitrite is measured weekly in the used fluid, with a change, partial exchange or suitable inhibitor required above 20 mg/l (TRGS 611, 2007). DGUV guidance dated 26 March 2024 describes inhibitor proof between 20 and 80 mg/l.

Can a tertiary amine such as TEA replace DCHA on its own?

Triethanolamine (TEA) can add buffering, but it is usually paired with another amine. STLE notes MEA and TEA have been used together for many years to balance neutralization, pH development and buffering (STLE, 2013). TRGS 611 also asks for high purity in tertiary amines carrying secondary amine impurities.

Related posts