Why a flocculant works in the jar test but not in the plant
Summary
A flocculant that works in the jar test but not in the plant usually points to mixing energy, polymer makedown, dose point or changed raw water. This assumes the jar used the same product grade and the plant's own water. To separate product from plant condition, run a side-by-side re-jar of the plant's feed solution against a fresh makedown.
ASTM D2035-19, the active ASTM practice for the coagulation-flocculation jar test, evaluates coagulants and coagulant aids "for the same water and the same experimental conditions" (ASTM, 2019).
For drinking water plant design, the Ten States Standards say rapid mixing should take no longer than 30 seconds and flocculation detention should be at least 30 minutes (Great Lakes-Upper Mississippi River Board, 2022).
One maker's dry polymer data sheet suggests makedown at 0.1 to 0.5% polymer by weight, 30 to 60 minutes of aging, and gives a solution shelf life of 8 to 16 hours (Harcros Chemicals, accessed 2026).
The Ten States Standards say the design engineer should determine the appropriate G value and detention time through jar testing (Great Lakes-Upper Mississippi River Board, 2022).
This applies to polymer flocculants, used alone or after a coagulant, that were chosen in a jar test and feed a gravity clarifier or thickener. Sludge dewatering polymers on presses or centrifuges are judged by other bench tests and are not covered. The drinking water design values quoted here are reference points, not limits for an industrial plant.
What are the most likely causes when a flocculant works in the jar test but not in the plant?
When a flocculant works in the jar test but not in the plant, the most likely causes are five plant conditions the jar did not copy: mixing energy and time, polymer makedown and age, dose point and pump output, raw water drift, and clarifier load. A product defect is possible, but test it last, because each of these conditions can defeat a correct product.
Flocculation mixing energy and time differ from the jar
On the jar tester, floc forms under gentle paddles. In the plant, a pump, a valve or a turbulent inlet can tear it apart, and a flocculation stage shorter than the jar's slow mix can leave it too small.
Polymer makedown and age differ from the jar solution
The jar is usually dosed from a fresh lab solution. The plant feeds from a day tank, and that solution may be under-aged, held too long or made up at a different strength.
Flocculant dose point and pump output differ from the set dose
A worn pump, an air-bound suction line or a poorly mixed dose point means the water gets less polymer, or gets it in the wrong place.
Raw water has drifted from the jar sample
Today's pH, solids, temperature or load may no longer match the jar's bucket.
Clarifier load is higher than the jar's quiet settle
A jar settles in still water. A clarifier at high surface loading, with a broken rake or short-circuiting, carries over floc that would have settled in the jar.
Does plant mixing energy and contact time match the flocculant jar test?
You only know whether plant mixing energy and contact time match the flocculant jar test once you have compared the plant's velocity gradient (G) and residence time at each stage with the jar's paddle speeds and minutes. G is the measure of mixing intensity that design standards use for both rapid mixing and flocculation (Great Lakes-Upper Mississippi River Board, 2022).
Drinking water design values show how much time and gentleness flocculation needs. The Ten States Standards say rapid mixing should be instantaneous but not longer than thirty seconds, and floc formation should have at least 30 minutes of detention with tapered mixing, at a flow-through velocity of 0.5 to 1.5 feet per minute "to prevent floc from settling, tearing apart or shearing" (Great Lakes-Upper Mississippi River Board, 2022). Oregon guidance cites G values of 60 to 70 per second at the start of slow mixing and 10 to 30 per second at the end, with 10 to 30 minutes of total flocculation time typical (Oregon Health Authority, citing Kawamura, 2000). Tapered mixing starts stronger and ends gentler.
A jar run with 5 minutes of slow mixing at 30 rpm (California State Water Resources Control Board, 2020) says little about a plant where flocculated water travels a short, turbulent pipe to the clarifier. Before judging the product, calculate each plant stage's actual time at today's flow (tank volume divided by flow), check that the paddles turn at their set speed, and re-run the jar at the plant's times.
How do polymer dilution and aging change flocculant performance in the plant?
Polymer dilution and aging change flocculant performance because a dry polyacrylamide needs time in solution before it works fully. A solution held too long or mixed too hard delivers less activity at the same nominal dose. These are exactly the points where the jar and the plant often differ.
One maker's data sheet for a dry polymer puts numbers on this. It suggests adding the polymer into the vortex of a mixed tank at 0.1 to 0.5% polymer by weight, mixing at slow speed with 300 rpm as the maximum, aging the solution 30 to 60 minutes before use, and it gives a solution shelf life of 8 to 16 hours (Harcros Chemicals, accessed 2026). Values differ by grade, so read the data sheet for the grade you use.
Jar procedures often make their stock solutions with distilled or deionized water (California State Water Resources Control Board, 2020); the plant uses service water. On site, check four things against the data sheet: the weighed polymer and water per batch, which give the true strength; the time between makedown and use; the mixer speed; and the makedown water source. Follow the product SDS for handling dry polymer and cleaning up spills. If the day tank falls outside the data sheet on any of these points, correct the makedown before you change the dose or the product.
Does the dose point or dosing pump explain the flocculant jar test mismatch?
The dose point or dosing pump explains the flocculant jar test mismatch in two cases: the dose the water actually receives differs from the set dose, or the polymer enters where it cannot mix before floc forms. A drawdown, timing the drop in the pump's calibration column, measures the dose actually received. The pump setting is not proof of the dose.
The Ten States Standards say positive displacement solution feed pumps should be installed with "calibration tubes or mass flow monitors which can be used to physically measure the actual feed rates", and that a means to measure the flow being dosed shall be provided to determine chemical feed rates (Great Lakes-Upper Mississippi River Board, 2022). Use both. At the running pump setting, time the drop in the calibration column, then calculate the delivered dose: solution flow times solution strength, divided by plant flow measured at the same time. For example (illustrative), 60 L/h of a 0.2% solution into 300 m3/h of water delivers 0.4 mg/L of polymer.
Then walk the dose point. In the jar, the polymer goes into a known vortex at a known time after the coagulant. In the plant, check whether it enters before the coagulant has finished mixing, at a point with no turbulence, or so far upstream that the floc breaks before the clarifier. The same standard says consideration should be given to optimizing chemical feed point locations (Great Lakes-Upper Mississippi River Board, 2022).
Has the raw water changed since the flocculant jar test?
Raw water has changed since the flocculant jar test whenever today's feed differs from the jar sample in pH, suspended solids, temperature or load. A dose chosen for one water does not automatically carry over to another, so treat raw water drift as a plant condition, not a product fault.
One water utility's jar test procedure names four factors that can influence clarification performance: raw water quality, mixing conditions, polymer chemistry and dosage rate (Ugu District Municipality, 2024). Oregon guidance notes that temperature and pH also affect the flocculation process (Oregon Health Authority, citing Kawamura, 2000). The Ten States Standards, written for drinking water plants, say coagulant addition should be adjusted with changing raw water conditions based on jar testing (Great Lakes-Upper Mississippi River Board, 2022). In a California jar test field study, many plants were jar tested on visits in different seasons (California State Water Resources Control Board, 2020).
Pull the jar sheet and put its raw water values beside the plant's readings for the hours when settling failed. Industrial wastewater can change faster than surface water, with batch discharges, cleaning cycles and shift changes. If any value has moved outside the range of the jar sample, collect a fresh sample of the failing feed and re-jar on it before you judge the product.
How do you tell a flocculant product problem from a plant condition problem?
To tell a flocculant product problem from a plant condition problem, run a side-by-side re-jar on today's raw water at the plant's own mixing times. Dose one jar from the plant's day tank solution, one from a fresh makedown of the lot in use, and one from a fresh makedown of the retained sample, the product kept back from the lot that passed the original jar test. The pattern across the three jars decides it.
The table below lists the site checks and what each result points to: plant condition or product.
Check | What you see | Points to |
|---|---|---|
Plant stage times and paddle speed vs the jar | Plant flocculation shorter or harsher than the jar | Plant condition: mixing |
Day tank strength and age vs data sheet | Outside the maker's range, such as aged less than the 30 to 60 minutes one data sheet gives (Harcros Chemicals, accessed 2026) | Plant condition: makedown |
Pump drawdown vs set dose | Delivered dose below set dose | Plant condition: dosing |
Raw water pH, solids, temperature vs jar sample | Outside the jar sample's range | Plant condition: raw water |
Clarifier surface loading and rake | Flow above design, rake stopped, short-circuiting | Plant condition: hydraulics |
Re-jar: day tank solution vs fresh makedown of lot in use | Day tank jar fails, fresh jar passes | Plant condition: makedown or storage |
Re-jar: lot in use vs retained sample of approved lot | Lot in use fails, retained sample passes | Product: lot difference |
All three jars pass, plant still fails | Jar and plant disagree on the same day | Plant condition: mixing, dose point or hydraulics |
The deciding row is the last re-jar comparison. Only when the lot in use fails and the retained sample passes, on the same water and at the same dose, is the product the likely cause. Every other pattern sends you back to the plant. For how to present that evidence to a supplier or customer, see How to show whether a product complaint is really the product.
When should you call the flocculant supplier about a jar test mismatch?
Call the flocculant supplier about a jar test mismatch in three cases: the re-jar points to the lot in use; the plant checks are done and the plant still fails at a confirmed delivered dose; or the raw water has moved outside what the grade was selected for. Calling earlier usually ends in a dose increase that hides the real cause.
Bring the evidence the supplier needs to answer quickly: the original jar sheet with paddle speeds, times and raw water values; the day tank makedown log; the drawdown result and plant flow; the raw water readings for the failing period; the lot numbers and certificates of analysis for the lot in use and the approved lot; and the retained sample. Then ask the supplier three questions: whether the certificate of analysis for the lot in use differs from the approved lot, which makedown strength and aging time the maker recommends for that grade, and whether the grade still fits the new raw water.
Lubinpla, an applied AI company that structures technical reasoning in specialty chemicals, works a case like this from your own documents and site condition history: it separates what the use conditions explain from the product verdict and returns one cited document for your review. Keep the retained sample sealed and labeled until the case is closed; it is the only reference for the approved lot.
Frequently asked questions
How often should you re-run a flocculant jar test?
Re-run a flocculant jar test whenever the raw water, the product lot or the plant flow changes enough to move settling, and after any change to mixers or dose points. Seasonal swings in temperature and load are a common trigger. A fixed calendar interval misses the change that matters.
Can you copy the jar paddle rpm directly to the plant?
No. Paddle rpm depends on the jar shape and paddle, so the same rpm gives a different mixing intensity in a different jar. Compare velocity gradient and time instead, using the jar tester maker's G curve for that jar, and match the plant's measured stage times.
Should the jar test polymer solution use distilled water or plant water?
Many jar procedures make stock solutions with distilled or deionized water, but the plant makes down polymer in service water. When you investigate a mismatch, make one jar solution with the plant's own makedown water, so any effect of that water shows up in the jar.
Can overdosing a flocculant make the plant fail when the jar passed?
Yes, it can. A jar series across several doses usually shows settling improve up to a point and then worsen. A plant dose raised in response to poor settling can move past that point. Re-jar across a dose range before raising the plant dose further.