Lubinpla

How to plan a changeover trial when changing quench oil

Summary

A quench oil changeover trial takes 5 steps: cooling curve baselines, reference parts, tank cleaning, flash point check and stop criteria fixed before quenching. The plan applies to a hydrocarbon quench oil that replaces a used oil in the same tank. Compare curves only from the same probe and bath temperature, and write every limit before the first load.

  • ASTM D6200-21(2026) evaluates quench oils in a non-agitated system, and ASTM states there is no correlation between its results and results in agitated systems (ASTM D6200-21(2026), 2026).

  • In typical D6200 practice the Inconel 600 probe is heated to 871 °C and quenched into 1 to 2 liters of unagitated oil, usually at 60 °C for cold oils (MacKenzie, 2017).

  • Idemitsu staff advise reducing water when the water content of a quench oil is more than 200 ppm, to ensure uniform cooling (Ichitani and Steiger, 2018).

  • NFPA 86 (2015 edition), as summarized by MacKenzie, calls for a quench tank sized so the maximum quenchant temperature is not less than 28 °C (50 °F) below the flash point (MacKenzie, 2023).

This plan covers hydrocarbon quench oils, cold or martempering, replacing a used oil in an existing tank. It does not cover aqueous polymer quenchants, salt baths or gas quenching, and it gives no hardness limits for a specific steel. Fire protection for the tank follows NFPA 86 or your local fire code, not this guide.

What do you need before a quench oil changeover trial?

Before a quench oil changeover trial, you need the used oil's history, the new oil's technical data sheet (TDS) and safety data sheet (SDS), one cooling curve laboratory, a set of reference parts with their drawings, and the tank cleaning procedure. Gather it before you order the full fill.

  • Used oil history: recent cooling curves, viscosity, water content and acid number, plus the hardness and distortion record of the parts it quenched. ASTM D6710-21(2026) is a guide for choosing test methods for the quality and aging of hydrocarbon quench oils, and it gives no specific limits (ASTM D6710-21(2026), 2026).

  • New oil data: flash point, recommended operating temperature range and the SDS.

  • A retained sample of the new oil, sealed and dated. It serves as the control for every later cooling curve.

  • One laboratory and one probe for all curves, so any difference comes from the oil, not the test.

  • Reference parts: the steel grade and section that are hardest to harden, and the part with the worst distortion history.

  • The cleaning procedure, the waste route for used oil, and the tank's fire protection checks under NFPA 86 or the local fire code.

Name the person who signs off each step and the person who can stop the trial.

The used oil's history also tells you which problem the new quench oil has to solve. Idemitsu staff list improper oil selection, oxidative polymerization, pyrolysis and additive consumption as causes of failure to reach as-quenched hardness (Ichitani and Steiger, 2018).

Which cooling curve baseline should you fix for new and used quench oil before the changeover?

Before any part goes into the new oil, fix ASTM D6200-21(2026) cooling curves for both the used quench oil and the new oil, run on the same probe, at the same bath temperature and in the same laboratory. ASTM states that the test "provides a cooling time versus temperature pathway which is directly proportional to physical properties such as the hardness obtainable upon quenching of a metal" and that results may guide comparison of oils, new or used (ASTM D6200-21(2026), 5.1).

The test runs in still oil, and ASTM states there is no correlation between its results and those obtained in agitated systems (ASTM D6200-21(2026), 1.2). Read the two curves as a ranking of the oils, not as a forecast of hardness in your agitated tank.

In typical practice the Inconel 600 probe is heated to 871 °C and quenched into 1 to 2 liters of unagitated oil, at 60 °C for cold oils or 121 °C for martempering oils (MacKenzie, 2017). ISO 9950:1995, last confirmed in 2022, ranks quench oils with a nickel-alloy probe in non-agitated oil and serves the same purpose where ISO methods are specified (ISO, 2022).

For both oils, record the maximum cooling rate and the temperature at which it occurs, and put the bath temperature on every report. The retained new-oil sample stays the control for later curves, the same way MacKenzie compares used oils from four customers against new oil tested at 60 °C (MacKenzie, 2017).

Which parts should you measure for hardness and distortion in a quench oil changeover trial?

Measure the same reference parts, from fixed load positions, for as-quenched hardness and distortion: first in the used quench oil, then in the new oil. Both properties follow cooling power, so a trial that checks only hardness can pass an oil that bends parts. Idemitsu staff call quenching distortion the most common quality defect in heat treatment and classify it as distortion increment, distortion variation and time-dependent change (Ichitani and Steiger, 2018).

  1. Choose the part with the thickest section in the hardest-to-harden grade, and the part with the worst distortion history.

  2. Mark load positions: top, middle and bottom of the load, at the center and at the edge.

  3. To set the baseline, quench the same number of parts at each position in the used oil, at normal load, temperature and agitation. Three parts per position is only an illustrative count.

  4. Measure surface hardness, and core hardness on a sectioned part where the drawing calls for it, with the same tester and test locations each time.

  5. Measure distortion on the same features, such as runout, flatness or bore size, before heat treatment and again after quenching.

  6. Repeat with the new oil at the supplier's recommended temperature.

Write the pass bands for hardness and distortion before the first new-oil load. Fixing controls and criteria before any result arrives is the core of how to write a plant trial plan for a new chemical product, and a quench oil trial uses the same structure.

How do you clean the tank and limit carryover of old quench oil?

Clean the quench tank by fully draining the used oil, removing sludge and water, and checking the first fill before production, because Idemitsu staff advise "Do not mix new oil with degraded oil" (Ichitani and Steiger, 2018). Sludge deposited on parts creates uneven cooling and soft spots (Ichitani and Steiger, 2018), so a new fill poured over old sludge carries the defect forward.

  1. Cool the oil to the draining temperature set by the SDS and the site procedure. Isolate heaters, agitators and the furnace door under the site lockout procedure, and keep ignition sources away as the SDS directs.

  2. Drain through the lowest point and pump out the remaining oil.

  3. Remove sludge from the floor, coils and cooler. Centrifuging can remove sludge from oil in service (Ichitani and Steiger, 2018).

  4. Check the cooler and the roof above the tank for water entry. MacKenzie reports that in at least half of poorly functioning quench oils, water had entered the oil, causing cracking, uneven hardness and soft spots (MacKenzie, 2017). A tiny amount of water, about 0.1 percent, can make the bath foam and greatly increase the danger of fire (MacKenzie, 2017).

  5. Send used oil, sludge and wipes to disposal under the SDS disposal section and your local used oil or hazardous waste rules.

  6. Fill with new oil, circulate it at operating temperature and test water content before the first load; above 200 ppm, dry the oil first (Ichitani and Steiger, 2018).

How much flash point margin should a new quench oil keep at tank temperature?

A new quench oil should keep its maximum quenchant temperature at least 28 °C (50 °F) below its flash point under NFPA 86 (2015 edition), as MacKenzie summarizes it; check the edition your fire authority enforces. He adds a further 28 °C (50 °F) safety factor for hung loads and failed heat exchangers (MacKenzie, 2023). The margin applies to the peak temperature after a full load enters the tank, not to the idle bath temperature.

The table works through MacKenzie's example for a typical cold oil; its figures are illustrative.

Step

Value

Flash point of a typical cold oil

177 °C (350 °F) (MacKenzie, 2023)

NFPA 86 margin

minus 28 °C (50 °F) (MacKenzie, 2023)

Additional safety factor

minus 28 °C (50 °F) (MacKenzie, 2023)

Maximum peak quench temperature

121 °C (250 °F) (MacKenzie, 2023)

Temperature rise from a load of about one pound of parts per gallon of oil

minus 39 °C (70 °F) (MacKenzie, 2023)

Maximum operating temperature

82 °C (180 °F) (MacKenzie, 2023)

In this example, an oil with a 177 °C flash point runs at 82 °C at most before the load enters (MacKenzie, 2023).

Measure the delivered batch's flash point by ASTM D92-24, the Cleveland open cup method for petroleum products with flash points above 79 °C and below 400 °C, except fuel oils (ASTM D92-24, 2024). ASTM notes that flash point is only one of the properties to consider in assessing flammability hazard (ASTM D92-24, 5.1), so the tank's fire protection stays in force.

Which results should stop a quench oil changeover trial?

A quench oil changeover trial should stop when as-quenched hardness or distortion leaves its band, when the new oil's cooling curve drifts from its own baseline, when water or old oil shows up in the tank, or when the flash point margin shrinks. Write each limit, and the person who acts on it, before the first load.

Use the table to decide whether the trial continues, adjusts or stops. Its actions are illustrative.

Check

Pass

Fail and what to do

Cooling curve against the baseline

Same probe and bath temperature; curve close to the retained new-oil curve

Retest; if confirmed, stop and ask the supplier

As-quenched hardness

Inside the band written before the trial, at every load position

Stop; check agitation, oil temperature and load position before judging the oil

Distortion on reference parts

Inside the band for each measured feature

Stop; review oil temperature and agitation with the supplier

Residual old oil and water

Tank clean; water not above 200 ppm (Ichitani and Steiger, 2018)

Dry or replace the oil and find the water source

Flash point margin

Peak temperature at least 28 °C below flash point (MacKenzie, 2023)

Stop loads; lower the operating temperature or the load size

The hardness row matters most. A soft part at one load position points first to agitation or water, and only then to the oil.

Log every stop decision with its date, load number and readings. When two rows fail together, call the oil supplier and a heat treatment metallurgist.

Lubinpla's trial preparation builds a quench oil trial plan like this one from your own SDS, TDS and site records, fixes the test parts, controls and criteria before any result comes in, and returns one cited document for your review.

Frequently asked questions

Can you top up a degraded quench oil with the new oil instead of a full change?

No, not while the old oil is degraded. Idemitsu staff advise against mixing new oil with degraded oil, and against mixing oil dragged out on parts with the oil in the quench tank (Ichitani and Steiger, 2018). Topping up an oil that is still in good condition with the same product is a different case.

Why can a used quench oil's cooling curve look faster than the new oil's?

Water and pyrolysis, the breakdown of the oil by heat, both raise cooling performance. In Idemitsu's tests, adding 10% of oil decomposed in its sealed tube test increased cooling performance, and water in the oil raised cooling performance unevenly (Ichitani and Steiger, 2018). A faster curve on used oil is not proof that it quenches better.

How should a new quench oil be monitored after the changeover?

Go back to routine testing once the new oil has run a full production cycle inside the trial limits. ASTM D6710-21(2026) lists test methods for quality and aging of hydrocarbon quench oils without setting limits (ASTM D6710-21(2026), 2026), so the testing interval and limits come from your trial results and the supplier.

Related posts