Same chemical, different trade names: matching TDS, SDS and CoA
Summary
Four checks match one chemical across regional trade names: the same manufacturing site, the same safety data sheet (SDS) Section 3 composition, the same TDS specification, and written supplier confirmation. Hazard classes, exposure limits and registration numbers may still differ between the regional safety data sheets, because each jurisdiction classifies and regulates on its own terms.
US OSHA requires Section 3 of a safety data sheet for a substance to give the chemical name, common name and synonyms, and the CAS number or other unique identifier (OSHA, 2024, 29 CFR 1910.1200 Appendix D).
Where a US supplier claims an ingredient concentration as a trade secret, the safety data sheet shows one of 13 ranges prescribed in 29 CFR 1910.1200(i)(1)(iv), from 0.1% to 1% up to 80% to 100% (OSHA, 2024).
In the EU, a mixture's product identifier consists in part of its trade name or designation, and Section 1.1 gives it as on the label in the official language(s) of the Member State where it is placed on the market (European Commission, 2020, Regulation (EU) 2020/878).
A REACH registration number is issued per jurisdiction, such as EU, UK or Korea REACH, and is valid only within that region (Ricardo, 2025).
This method covers industrial chemicals sold by one manufacturer under different trade names in different regions. It does not prove that products from two different manufacturers are equivalent, and it does not replace a regulatory review when a product enters a new jurisdiction.
How do you match the TDS, SDS and CoA of one chemical sold under different trade names?
Four checks match the TDS, SDS and CoA of one chemical sold under different trade names. Run them in this order: each check costs less than the one after it.
Confirm the manufacturer and site. Read the manufacturer named in SDS Section 1 and on each certificate of analysis (CoA). Two trade names made at one site are a candidate match; two sites mean two products until the supplier says otherwise.
Compare SDS Section 3 line by line. List every CAS number from both safety data sheets with its concentration or range. Every CAS number listed on both must have overlapping ranges. A CAS number listed on only one can come from different disclosure rules: Section 3 must list ingredients classified as health hazards above cut-off limits in that jurisdiction (OSHA, 2024, 29 CFR 1910.1200 Appendix D), and an EU supplier may add the rest (European Commission, 2020, Regulation (EU) 2020/878). Ask the supplier to explain it in writing.
Compare the technical data sheets (TDS) and CoA limits. Put the typical values and test methods from both TDS side by side, then the CoA specification limits for each name. The same methods with matching limits support one product.
Get a supplier letter. Ask for a dated, signed statement that names both trade names, the manufacturing site and the formulation, and states that they are the same product.
File the letter with the product's documents, the same way a distributor organizes TDS, SDS and CoA files from many suppliers.
Why does the same chemical product carry different trade names by region?
A trade name has to work in a local market, under local rules, and often through the local company that sells it, so one chemical product can carry a different name in each region. Common reasons are a trademark registered by another party in one country, an older name kept after a merger or acquisition, a regional sales company that brands its own range, and a name chosen to suit the local language (illustrative list of common commercial reasons).
Regulation shapes the paperwork more than the name itself. In the EU, the product identifier for a mixture consists in part of its trade name or designation (ECHA, 2020, citing Article 18(3)(a) of CLP), and Section 1.1 of the safety data sheet gives that identifier as it appears on the label, in the official language(s) of the Member State where the product is placed on the market (European Commission, 2020, Regulation (EU) 2020/878). So a regional name usually arrives with a regional label and a regional safety data sheet, written for that market's classification and language.
This is how one product ends up in a supplier's catalog three times. The names differ, the regional sections of the documents differ, and the chemistry behind them may be identical. The checks in this post separate that case from a reformulated product that only kept a similar name.
Which SDS sections show that two trade names are the same chemical?
SDS Sections 1 and 3 carry the evidence. Section 1 gives the product identifier, any other names and the supplier; Section 3 lists the composition. Under US OSHA, Section 3 for a substance gives the chemical name, common name and synonyms, and the CAS number (OSHA, 2024, 29 CFR 1910.1200 Appendix D). Under EU Annex II, Section 1.1 may list "other names or synonyms by which the substance or mixture is labelled or commonly known" (European Commission, 2020, Regulation (EU) 2020/878).
Read Section 3 with the regional rules in mind. A US safety data sheet that claims a concentration as a trade secret shows one of 13 ranges prescribed in 29 CFR 1910.1200(i)(1)(iv), such as 30% to 60% (OSHA, 2024), while an EU safety data sheet may give exact percentages or ranges of percentages in descending order (European Commission, 2020, Regulation (EU) 2020/878). Two different ranges can describe the same formulation, so check that they overlap, not that they match.
Further identifiers help in the EU. A unique formula identifier (UFI) normally corresponds to one mixture composition only (ECHA, 2020), so the same UFI under two names is strong evidence.
Other sections prove nothing. Section 15, the transport data in Section 14 and the emergency number in Section 1 are regional, so they do not show identity either way.
What if the regional SDS for the same chemical shows different hazard classes?
Different hazard classes on the regional safety data sheets of one chemical are usually expected and do not by themselves point to two products. Each jurisdiction applies its own version of the Globally Harmonized System (GHS). A chemical may be classified differently in each country, which changes the label, the hazard and precautionary statements, and the precautionary measures (Ricardo, 2025). US OSHA updated its Hazard Communication Standard to align primarily with GHS Revision 7, in a final rule published on May 20, 2024 (OSHA, 2024), while other regions apply other revisions.
The exposure limits in Section 8 differ for a similar reason. In the EU, Section 8.1 lists the national limit values applicable in the Member State where the safety data sheet is provided (European Commission, 2020, Regulation (EU) 2020/878), and the US Section 8 lists the OSHA PEL and ACGIH TLV where available (OSHA, 2024, 29 CFR 1910.1200 Appendix D). REACH registration numbers appear only on the safety data sheets for the jurisdiction that issued them (Ricardo, 2025).
A different classification becomes a warning sign only when the regional rules cannot explain it. For example, an ingredient appears on one SDS only although it is classified as hazardous above the cut-off limits in both jurisdictions, or shared ingredients have ranges that do not overlap. Then ask the supplier which formulation each name covers before you treat them as one product.
Which trade name should go on customer documents?
Use the name printed on the label and safety data sheet the customer actually receives in their market. A quote, order confirmation or technical recommendation under another region's name sends the customer looking for documents that do not match their delivery.
Keep the other names as cross-references, not as the main name. A line such as "also sold as [other trade name] in [region]" lets the customer's purchasing and quality teams link their files, but it is accurate only after the four checks pass. Without a supplier letter, write that the products are under review, not that they are the same.
Match the documents to the name. Send the safety data sheet for the customer's jurisdiction, in its official language where EU REACH applies: "The safety data sheet shall be supplied in an official language of the Member State(s) where the substance or mixture is placed on the market, unless the Member State(s) concerned provide otherwise." (European Union, 2006, REACH Article 31 paragraph 5). Send the CoA for the delivered batch, under the trade name on the label.
For pharmaceutical ingredients, ICH Q7 recommends that a CoA show the name, address and telephone number of the original manufacturer (ICH, 2000, Q7 section 11.43). Industrial chemicals have no such general rule, so ask the supplier for those details.
How do you check a regional trade name match before quoting?
Run the table below against the documents for both names before you quote. A match holds only when every row passes; each row also says what to do when the evidence does not support one product.
Check | Same product if | Different or unclear: what to do |
|---|---|---|
Manufacturer and site | Same company and site on SDS Section 1 and CoA | Ask which site makes each name |
SDS Section 1 identifiers | Other names list the second trade name, or same UFI | Ask the supplier to add the synonym |
SDS Section 3 CAS numbers and ranges | Shared CAS numbers have overlapping ranges; any one-sided CAS explained by disclosure rules | Ask the supplier to explain each one-sided CAS in writing |
TDS typical values | Same values on the same test methods | Request both TDS on one method |
CoA specification limits | Same limits and methods on recent batches | Request CoAs from two recent batches |
Supplier letter | Signed, dated, names both trade names and site | No letter: do not call them the same |
The Section 3 row decides most cases. Explain first any CAS number that appears under one name and not the other. It can mean a different formulation or only a different disclosure threshold, so accept no supplier letter until that difference is explained in writing.
When any row fails, ask the supplier's regulatory or product stewardship contact, not only sales: only the manufacturer knows the formulation behind each name. Lubinpla's data room can group a product line's regional brand names as aliases of one brand, so the TDS, SDS and CoA filed under either name are found together; it does not compare their contents, so the checks above stay with a person.
Frequently asked questions
Can two trade names share one safety data sheet?
Yes, in some cases. EU Annex II allows a single safety data sheet to cover more than one substance or mixture where its information meets the requirements for each of them (European Commission, 2020). Each name must still appear on it, and regional rules still decide which version a market receives.
Does a matching CAS number prove two products are the same?
No. A matching CAS number shows the same main substance, but grade, purity, impurities, additives and physical form can still differ. So the check covers the TDS values, CoA limits and supplier letter, not only Section 3.
How often should a trade name match be rechecked?
Recheck it whenever either safety data sheet gets a new revision date, the supplier changes the manufacturing site, or a CoA shows a new test method or limit. A match confirmed for one formulation does not carry over to a reformulated product that kept its name.