윤활유·금속가공유
윤활유·금속가공유 분야는 설비를 돌리는 오일, 그리스, 유체와 금속을 절삭·연삭·성형하는 유체를 다룹니다. 가이드는 설비와 공정별로 나뉩니다. 기어박스, 베어링, 유압, 압축기, 터빈, 체인, 차량·장비, 오일 분석, 절삭 가공, 금속 성형, 그리고 모든 윤활유에 공통인 기초입니다.
윤활 기초: 점도, 기유, 첨가제
-
Synthetic vs Mineral Oil: Differences for Industrial Lubricants
Mineral oil suits moderate temperatures and normal drains; synthetic oil suits temperature extremes and long life. Compare properties with test methods.
산업용 기어유와 기어박스 윤활
-
ANSI/AGMA 9005-F16: What It Requires for Industrial Gear Oils
ANSI/AGMA 9005-F16 sets rust, copper, foam, oxidation and demulsibility limits for gear oils, plus FZG and FE8 tests for antiscuff oils. See the table.
-
Industrial Gear Oil vs Automotive Gear Oil: Grades and Additives
Industrial gear oil suits enclosed gearboxes graded by ISO VG; automotive gear oil suits hypoid axles graded by SAE J306 and API GL. See the table.
-
Why an Industrial Gearbox Overheats and How to Fix It
Industrial gearbox overheating usually comes from a wrong oil level or viscosity, overload, misalignment or a blocked cooling path. Check each one on site.
-
FZG Scuffing Test ISO 14635-1: What It Tells You About Gear Oil
ISO 14635-1:2023 (FZG A/8.3/90) finds the load stage at which an oil lets test gears scuff: a relative scuffing ranking, not field life. How to read it.
유압유와 유압 시스템
-
Why Hydraulic Oil Turns Milky: Water or Air and How to Tell
Milky hydraulic oil means emulsified water, entrained air or both. A settle test and a Karl Fischer result tell them apart and show where to look next.
-
Can You Mix Hydraulic Oils? When It Is Safe and When It Is Not
Only if base fluid, classification and viscosity grade match and the supplier confirms it. Never mix mineral oil with polyglycol or water glycol fluids.
-
ISO 12922 Explained: Requirements for Fire-Resistant Fluids
ISO 12922:2020 sets minimum requirements for HFAE, HFAS, HFB, HFC, HFDR and HFDU fluids. See what each category must meet and how to verify compliance.
-
ISO 46 vs AW 46 Hydraulic Oil: What the Two Labels Tell You
ISO 46 is only a viscosity grade; AW 46 is an ISO 46 oil with antiwear additives. See when plain R&O oil is enough and when pumps need the antiwear type.
-
Why Hydraulic Oil Overheats and How to Find the Real Cause
Hydraulic oil overheats from relief valve bypass, internal leakage or a fouled cooler. Use this site check table to find which one raises your temperature.
-
TSCA PIP (3:1) Rule: What It Means for Phosphate Ester Fluids
Under TSCA, PIP (3:1) hydraulic fluids are allowed only for aviation or military-spec uses. What the 2025 revision changed and what fluid users do now.
-
Ester Fluid Failure: How a Hydrostatic Pump Loss Was Traced
A 300 kW ester hydrostatic drive lost its pumps in 12 months. How the published case traced it to loop overheating and fluid oxidation, and what to check.
-
Types of Hydraulic Oil and Where Each One Should Be Used
HM antiwear oil suits most systems, HV wide temperature swings, HFx fluids fire risk and HEx fluids leaks to water. See each hydraulic oil type and use.
압축기, 진공 펌프, 냉동기 오일
-
Compressor Oil vs Motor Oil: Why Detergent Engine Oil Fails
Compressor oil uses low-ash additives that limit carbon on hot discharge valves; motor oil carries detergents for soot. How they differ, when to use each.
터빈, 발전기, 변압기 오일
-
Transformer oil test limits in service: what each result means
IEC 60422:2024 sets in-service limits for breakdown voltage, water, acidity, IFT and dissipation factor by category. See example limits and actions.
-
Transformer fluid choice: mineral oil, ester or silicone?
Mineral oil for outdoor units, natural ester for sealed units at fire or spill risk, synthetic ester for free-breathing units needing a high fire point.
-
Stockholm PCB deadlines 2025 and 2028: what they mean for oil
Stockholm Convention parties aimed to end PCB equipment use by 2025 and manage PCB liquids soundly by 2028. What owners of transformer oil must do now.
-
Moisture in transformer paper and oil: how temperature moves it
Warming pushes water from transformer paper into oil and cooling pulls it back slowly, so an oil moisture result shows paper moisture only at equilibrium.
오일 분석과 오염 관리
-
What is oil analysis in industrial condition monitoring?
Oil analysis tests used lubricant for oil condition, contamination and wear debris to catch machine problems early. See what it measures and how it works.
-
ISO 4406 vs SAE AS4059: which oil cleanliness code to specify
ISO 4406 codes particles per mL at three sizes; SAE AS4059 keeps NAS-style classes for aerospace. See how they differ and which to write into a spec.
-
ASTM D7843 MPC varnish test: what it tells you and what not
ASTM D7843 MPC reports varnish potential as Delta E, not deposits already in the system. Read results with temperature history, RULER and RPVOT trends.
-
Turbine oil varnish: why it forms while antioxidants remain
Varnish forms when degradation products from hot spots, micro-dieseling or static discharge exceed oil solvency, even with antioxidants left. Here is how.
-
How to choose oil analysis tests for each industrial machine
Pick oil analysis tests by machine and failure mode: viscosity, elements, water and particle count as a base, then ferrous debris, RPVOT or MPC as needed.
절삭유, 방전가공유, 슬라이드웨이유
-
Cutting Oil vs Coolant: Which Fits Your Machining Operation
Neat cutting oil suits slow, high-contact cuts such as broaching and threading; water-miscible coolant suits fast cuts that need heat removal. See table.
-
How to Choose Tapping Fluid for Aluminum Without Chip Welding
Choose a high-lubricity, chlorine-free tapping fluid for aluminum: chips welding to the tap usually limit tap life. Decision table by alloy, tap and hole.
-
How to Choose Cutting Oil for Stainless Steel Machining
Use an extreme-pressure neat oil to tap and thread austenitic stainless steel, and a tested chlorine-free EP oil where chlorine is restricted. See table.
-
Why Taps Break When Tapping Stainless Steel and How to Stop It
Tap breakage in stainless usually comes from work hardening, weak flank lubrication, chips packed in blind holes or too small a tap drill. Site checks.