Cooling tower conductivity: controller vs handheld meter readings
Summary
A cooling tower controller and a handheld conductivity meter usually disagree for one of three reasons: a fouled or uncalibrated probe, different temperature compensation, or different samples. Neither instrument is right by default. Check the handheld against a conductivity standard first, then read both instruments on one grab sample, compensated to 25 °C, before you recalibrate the controller.
Electrical conductivity increases by 0.5 to 3 percent per degree Celsius, depending on the ions present, so field readings are corrected to 25 °C (USGS, 2019).
Most meters use linear (0.019 to 0.020 per °C) or nonlinear (ISO 7888) temperature compensation, typically accurate to ±5 percent for water at 5 to 35 °C and pH 4 to 11 (USGS, 2019).
A standard read within ±3 percent of its certified value above 100 µS/cm counts as accurate and does not warrant recalibration (USGS, 2019).
If a reading changes by more than 5% after probe cleaning, Walchem's WCT manual says to clean the probe more often (Walchem, 2007).
This check applies to conductivity used for bleed control in open recirculating cooling towers, with water between 5 and 35 °C and pH between 4 and 11, where standard temperature compensation holds (USGS, 2019). Low-pH samples, controllers set to display ppm, and electrodeless sensors installed in metal or plastic pipe need the extra checks noted below.
What makes a cooling tower conductivity controller and a handheld meter disagree?
A cooling tower conductivity controller and a handheld meter disagree for five main reasons. Each leaves a different trace, and the comparison table in the next section uses those traces to tell them apart.
Probe fouling or scale on the controller electrodes
In warm, aerated tower water, scale and biofilm coat contacting electrodes. A carbonate film makes the water look less conductive than it is, so the controller bleeds less than it should (Plant Automation Technology, 2020).
Calibration drift in either instrument
The controller is calibrated to match a handheld meter or a standard solution (Walchem, 2007). A handheld that has drifted therefore passes its error straight to the controller.
Temperature compensation mismatch
Two instruments that use different compensation factors, or one with a faulty thermistor (the temperature sensor the compensation relies on), report different values for the same water at the same moment.
Cell constant or sensor type mismatch
The cell constant is the factor set by the probe's fixed cell geometry. A probe whose cell constant has shifted, or an electrodeless sensor affected by the pipe wall, reads differently from a clean dip probe.
Different samples
A grab sample taken at the basin is not the water passing the probe tee. And a tee that runs partly empty or carries air bubbles gives the controller a false reading.
How do you compare controller and handheld conductivity readings on the same sample?
Compare cooling tower controller and handheld conductivity readings on one grab sample drawn at the controller's probe tee, after the handheld has passed a check on a conductivity standard. Verify the handheld first: a reading within ±3 percent of the certified value above 100 µS/cm counts as accurate (USGS, 2019).
Then draw water from the sample valve next to the probe. Read the handheld with automatic temperature compensation on, and note the controller reading and the water temperature in the same minute. Let the handheld cell reach the sample temperature first, since insufficient thermal equilibration gives drifting readings (USGS, 2019). The table below separates the causes using that one grab sample and the history of earlier readings.
Check | What you see | Points to |
|---|---|---|
Handheld on a conductivity standard | Off by more than ±3 percent above 100 µS/cm (USGS, 2019) | Handheld calibration or a stale standard |
Gap across probe cleanings | Gap grows between cleanings, closes after cleaning | Fouling or scale on the controller probe |
Gap against water temperature | Gap changes as the water warms or cools | Temperature compensation or thermistor |
Controller self-test | Outside 1000 ±20 µS/cm on a WCT controller with a 10 ft cable (1 µS/cm lower per extra foot), and still outside with the sensor disconnected (Walchem, 2007) | Controller electronics, not the probe |
Reading against flow or fan state | Reading jumps when flow drops or the tee drains | Sample point, empty tee or air |
Sensor type | Electrodeless sensor calibrated in a beaker | Pipe wall effect on the cell constant |
The second row is the pattern you will see most often. A gap that grows week by week and closes after cleaning points to fouling, not to the handheld. If the handheld fails its own standard check, fix it first, because the controller is calibrated to match whatever the handheld reads (Walchem, 2007).
Does probe fouling make a cooling tower conductivity controller read low?
Probe fouling usually makes a cooling tower conductivity controller read low. Scale on contacting electrodes changes the fixed cell geometry and insulates the electrode surface. Plant Automation Technology (2020) describes a probe reading fifteen percent low that keeps the controller inside its band while dissolved solids climb past the scaling threshold. The reduced bleed then speeds further scaling. The USGS lists fouling or contamination of the conductivity cell among the sources of uncertainty in specific conductance measurement (USGS, 2019).
Walchem gives a simple test for a contacting probe on its WCT controllers: read and record conductivity, remove, clean and replace the probe, then read again. If the readings differ by more than 5%, increase the cleaning frequency (Walchem, 2007).
Track the correction each calibration needs. The USGS notes that changes in the cell constant that exceed 2 percent may be the result of a contaminated standard or dirty probe (USGS, 2019), and a probe that needs a growing correction from one quarter to the next is failing (Plant Automation Technology, 2020).
Electrodeless (toroidal) sensors resist fouling better because they do not rely on direct electrode contact, though they are not immune (Plant Automation Technology, 2020). Sensorex (2023) notes that the pipe wall changes their effective cell constant, so they should be calibrated in the field against a referee meter or in a container identical to the piping.
How does temperature compensation change cooling tower conductivity readings?
Temperature compensation corrects every cooling tower conductivity reading to 25 °C, so two instruments with different compensation settings disagree whenever the water is not at 25 °C. Electrical conductivity increases by 0.5 to 3 percent per degree Celsius, depending on the ions present (USGS, 2019). Most meters apply either a linear factor of 0.019 to 0.020 per °C or the nonlinear method of ISO 7888:1985, and meters with built-in compensation are typically accurate to ±5 percent for water at 5 to 35 °C and pH 4 to 11 (USGS, 2019).
As an illustrative case, take 35 °C tower water. If the handheld reports uncompensated conductivity while the controller reports at 25 °C with a factor of 0.020 per °C, the handheld reads about 20 percent higher on the same sample.
Three settings can cause a mismatch. First, one instrument is set to report uncompensated values, or to manual compensation at a fixed temperature; Walchem's WCT controllers offer both automatic and manual temperature compensation (Walchem, 2007). Second, the two instruments use different linear factors. Third, the controller's temperature reading is wrong; the WCT manual calibrates it against a thermometer (Walchem, 2007), and the USGS troubleshooting table lists incorrect temperature compensation as a cause of a meter that will not read standards accurately (USGS, 2019).
Low pH is a separate limit. Low-pH samples below pH 4 can carry errors as large as 50 percent with standard factors (USGS, 2019).
How do you fix each cause of a conductivity mismatch?
Fix a cooling tower conductivity mismatch by correcting the cause the comparison found, then recalibrating the controller to the verified handheld or a standard. Work in this order:
Handheld fails the standard check: replace an old or contaminated standard first, then recalibrate the handheld, choosing a standard close to the expected sample value (USGS, 2019).
Fouled controller probe: clean it with a cloth and mild detergent; for scale, Walchem's WCT manual specifies dilute (5%) hydrochloric acid (Walchem, 2007). Handle the acid with the protective equipment named in its Safety Data Sheet (SDS), and in the US keep that SDS accessible to workers as OSHA's Hazard Communication standard requires (OSHA, 29 CFR 1910.1200). Recalibrate after every cleaning (Walchem, 2007).
Compensation mismatch: set both instruments to report at 25 °C with the same factor, and check the controller thermistor against a thermometer (Walchem, 2007).
Self-test outside its range with the sensor disconnected: send the controller for service; if the self-test passes but calibration fails, the sensor or its wiring is at fault (Walchem, 2007).
Sample point: move the probe tee to a spot with an active sample, where the tee stays full (Walchem, 2007), and free trapped air from the cell (USGS, 2019).
Calibrate the controller only after the handheld has passed its standard check.
What should a site visit record when the two conductivity readings disagree?
A site visit record for a cooling tower conductivity mismatch should hold both readings, the difference between them, and enough context to show where each number came from. Plant Automation Technology (2020) recommends recording the handheld reading, the controller reading and the difference every time, because the difference is the number most logs leave out. It also recommends setting the action threshold in advance. The USGS asks for a log with every meter that records calibrations, cell constants and repairs (USGS, 2019).
Record these fields for each comparison:
Who measured, with which handheld (serial number), and the date and time of both readings
The sample point, such as the sample valve at the probe tee or the basin
The standard used, its certified value and lot, and the handheld's reading on it
Water temperature, and the compensation setting and factor on each instrument
Controller reading, handheld reading and the difference, before and after any cleaning
The action taken and the reading after recalibration
A reading without its sample point or standard check cannot settle which instrument was right. The same rules that make a technical service report the customer acts on apply to this record: the finding first, each reading with its evidence, and each action with an owner.
When should you call a water treatment specialist about conductivity drift?
Call a water treatment specialist about cooling tower conductivity drift when the controller and a verified handheld still disagree after cleaning and recalibration, or when the gap returns faster each time. A gap that reopens within days of cleaning means scale or biofilm is forming quickly on the probe. That suggests the same deposits are forming on the heat exchanger surfaces, which makes it a water treatment question rather than an instrument one.
Call the controller maker instead when the self-test fails, since the electronics need repair (Walchem, 2007).
A specialist should also review the case in three situations: when the cell constant shifts by more than 2 percent between calibrations without a contaminated standard to explain it (USGS, 2019), when the water pH falls below 4 and standard compensation no longer holds (USGS, 2019), or when the bleed setpoint was changed during a period of low readings and the true cycles of concentration are unknown.
Bring the comparison log, the cleaning dates and the calibration corrections. A specialist can judge a trend, not a single number. Lubinpla's site inspection works the same way: it attaches who measured, when, where and the range to every reading, and uses only readings that carry them as evidence for a judgment.
Frequently asked questions
How often should you compare a cooling tower controller with a handheld meter?
A weekly handheld comparison is the usual recommendation (Plant Automation Technology, 2020). For a new installation, Walchem recommends cleaning the probe after two weeks of service and then setting the cleaning interval from how much the reading changes after cleaning (Walchem, 2007).
Does changing a controller display from µS/cm to ppm affect the comparison?
Changing the display unit on a Walchem WCT controller does not convert the setpoints, so the bleed settings must be changed by hand (Walchem, 2007). Compare readings in µS/cm on both instruments, because a ppm display depends on the conversion factor each instrument uses.
Which standard covers conductivity measurement of cooling water?
ASTM D1125-23 covers electrical conductivity of water, including cooling water, with Test Method A for field and laboratory samples from 10 to 200 000 µS/cm and Test Method B for continuous in-line measurement from 5 to 200 000 µS/cm (ASTM D1125-23). ISO 7888:1985 covers the same measurement internationally.