Lubinpla

How to tell if a boiler water treatment program is working

Summary

To judge a boiler water treatment program, check feedwater hardness, condensate iron, tube deposits and inspections against ASME-based limits set before the review. Control tests such as sulfite, phosphate, alkalinity and conductivity show only that chemicals were fed and blowdown was held, not that scale and corrosion stayed away. This fits industrial and institutional steam boilers with test logs.

  • For industrial watertube boilers at 0 to 300 psig without a superheater or turbine drives, the ASME limits reproduced by the US Department of Defense set feedwater total hardness below 0.5 ppm as CaCO3 and total iron below 0.1 ppm (US DoD, 2026).

  • In a well-managed condensate system, iron in the returning condensate is frequently below 10 ppb (ChemTreat, 2023).

  • 90 percent or more of carbon steel corrosion products can exist as iron oxide particulates, so dissolved iron tests alone can grossly underestimate corrosion (Water Technology, 2021).

  • One boiler maker gives accepted deposit weight density thresholds for chemical cleaning of 40 to 20 g/ft2 below 1000 psi (Valmet, 2016).

This method fits industrial and institutional steam boilers up to about 1000 psig that keep test logs and open for inspection. Utility units, heat recovery steam generators and hot water boilers follow other guidance. The numeric limits quoted here come from public reproductions of ASME tables, so confirm each one against the current ASME edition you hold.

When should you review whether a boiler water treatment program is working?

Review a boiler water treatment program at fixed points: before a treatment contract renews, after a planned outage with a tube sample or internal inspection, after a program change, and after any tube failure or scale finding. Each of these moments gives you outcome evidence, meaning evidence of whether scale and corrosion stayed under control, rather than one more month of shift tests.

The review has one question to answer: did the program keep scale and corrosion under control in this boiler, at this pressure, with this makeup and condensate? Whether operators kept the chemical residuals in range is a separate question. A boiler can hold sulfite and phosphate inside their control ranges every shift and still collect iron deposits from a corroding condensate system. The residuals measure the treatment, not the damage.

The common reference for the limits is the ASME consensus on feedwater and boiler water chemistry for industrial and institutional boilers. It was first published in 1979, revised in 1994 and 1998, and the current document is a further expansion and revision (ASME, 2021). Take your thresholds from it, or from the boiler maker's limits where those are stricter.

Fix the criteria before anyone looks at the period's results. Criteria written after the data are in tend to drift toward whatever the data show, and then the review no longer tests the program. For a contract review, agree the criteria with the treatment supplier at the start of the period.

What boiler and condensate data do you need?

A boiler program review draws on four kinds of data: the shift test log, feedwater and condensate analyses that include total iron, deposit and inspection records from outages, and the operating context of the period. Without outcome data from the last two kinds, the review can say whether the program was run, but not whether it worked.

US Department of Defense guidance says logs for larger boiler plants "should provide a record of the treatment and test results of boiler water, makeup water, and condensate water" (US DoD, 2026). The same guidance applies this to plants above 15 psig steam with an output above 100 boiler horsepower, and says historical records should contain start-ups, shutdowns, occurrences of corrosion and scale, and equipment inspection results (US DoD, 2026).

Before you use the data, check that they can be trusted. The ASME sampling consensus states that the sample "must be truly representative of the stream being monitored", which requires a proper sampling system, adequate flushing, the right sample velocity and sound handling (Water Technology, 2006). It states that samples above 77 F (25 C) must be cooled before collection, and that accepted good practice requires purging at least 3 sample system volumes before a sample counts as representative (Water Technology, 2006).

Record the operating context as well: load swings, makeup percentage, condensate return rate, softener or deaerator outages and program changes. A month with a softener failure cannot be held to the same expectation as a month without one.

Which boiler control tests show only that chemicals were fed?

Boiler control tests such as sulfite or other scavenger residual, phosphate or polymer residual, alkalinity, neutralized conductivity and condensate pH show that chemicals were fed and blowdown was held. They do not show that scale and corrosion were controlled. They are the program's steering inputs: operators read them every shift to adjust feed and blowdown.

Chem-Aqua's test guide describes these tests in exactly those terms: neutralized conductivity is used to monitor blowdown requirements, the tracer or active test confirms that target inhibitor levels are kept in the boiler, and the sulfite test confirms the oxygen scavenger residual (Chem-Aqua, 2023). Most corrective actions in that guide are feed or blowdown changes.

That leaves two limits. A residual in range is necessary but not sufficient: it shows the chemistry was present, not that it prevented deposits on a high heat flux tube or corrosion in a condensate line. Residuals also respond to blowdown as much as to feed, so a residual held in range by cutting blowdown can hide a rising dissolved solids load.

Control tests can still warn you of trouble. Chem-Aqua notes that hardness in the feedwater can cause phosphate and alkalinity to drop (Chem-Aqua, 2023), so a falling phosphate residual with steady feed is a cue to check feedwater hardness. Read the control log for patterns like this, but score the program on the outcome evidence in the next section.

Which boiler results show scale and corrosion are controlled?

Whether scale and corrosion are under control shows in feedwater hardness and iron, condensate total iron, tube deposit weight density, corrosion coupon results and internal inspection findings. They measure what enters the boiler and what builds up inside it, and that is what the program exists to prevent.

Feedwater hardness and iron tell you the scale and deposit load coming in. The ASME limits reproduced in US Department of Defense guidance tie them to pressure: for industrial watertube boilers at 0 to 300 psig without a superheater or turbine drives, total hardness below 0.5 ppm as CaCO3, total iron below 0.1 ppm and dissolved oxygen below 0.007 ppm before scavenger addition (US DoD, 2026).

Condensate iron is the corrosion indicator for the return system; Chem-Aqua lists it as an "Indicator of corrosion" (Chem-Aqua, 2023). Test total iron, not only dissolved iron, because 90 percent or more of carbon steel corrosion products can exist as iron oxide particulates (Water Technology, 2021). Iron entering from condensate and economizers frequently deposits on boiler tubes (ChemTreat, 2023).

Deposit weight density from a tube sample is the direct scale measure. Power magazine describes taking a tube sample from the highest heat flux area at each major outage, or at least every two years, and judging by the most heavily deposited tube (POWER, 2014). Corrosion coupons tested by ASTM D2688-23 give corrosion rate in relative terms, so compare them with earlier coupons in the same position (ASTM International, 2023).

How do you set pass criteria for a boiler program before reviewing results?

To set pass criteria for a boiler program before you review results, write one line per outcome measure: the threshold with its source and pressure band, what you conclude if it is met, and what you do if it is not. Agree the lines with whoever runs the program, date them, and do not change them after the period's data arrive.

Take each threshold from one named source for the boiler's type and pressure band: the ASME consensus table, or the boiler maker's limits where they are stricter. Where no published limit exists, as for condensate iron in most industrial plants, use the plant's own baseline and judge the trend. Write the test method beside each line, because a total iron result and a dissolved iron result on the same water are not comparable.

The criteria table below decides, line by line, whether each outcome measure passes for an industrial watertube boiler at 0 to 300 psig with a deaerator and no superheater, turbine drives or steam purity restriction. Replace the values with those for your boiler's pressure and type.

Criterion

Threshold (source)

If met

If not

Feedwater total hardness

Below 0.5 ppm as CaCO3 (US DoD, 2026, ASME table)

Scale load into the boiler is controlled

Check softener capacity, regeneration and bypass, then condensate contamination

Feedwater total iron

Below 0.1 ppm (US DoD, 2026, ASME table)

Iron load into the boiler is controlled

Trace the source: condensate, economizer or makeup

Feedwater dissolved oxygen before scavenger

Below 0.007 ppm (US DoD, 2026, ASME table)

Deaerator is doing its share

Check deaerator venting and temperature before raising scavenger

Condensate total iron

No rising trend; below 10 ppb is frequent in well-managed systems (ChemTreat, 2023)

Return system corrosion is controlled

Check condensate pH, amine feed and air in-leakage

Tube deposit weight density, hot or cold side

Below the cleaning threshold, 40 to 20 g/ft2 below 1000 psi (Valmet, 2016)

Deposits are below cleaning level

Plan cleaning and find the deposit source

Internal inspection

No new scale, pitting or oxygen attack since last inspection (illustrative site criterion)

Program protects surfaces

Record location and type, link to the log period

The row that matters most is feedwater hardness. If it fails repeatedly or without a known cause, every boiler water result downstream is judged against a load the program was not designed to absorb, so fix pretreatment before you judge the chemistry.

How many boiler results outside control range are too many?

The tolerance for boiler results outside control range depends on the kind of result. One outcome result outside its limit, such as a hardness breakthrough, counts as a failure for the period. Control test excursions, meaning control results that leave their range, are judged by pattern, duration and cause. Write both rules into the criteria before the review.

For control tests, statistical process control checks whether the variation is ordinary. The NIST/SEMATECH handbook describes control limits at 3 standard deviations from the mean as "an accepted standard in industry", and lists the Western Electric rules for signaling an out-of-control process: any point beyond 3 sigma, 2 of the last 3 points beyond 2 sigma, 4 of the last 5 beyond 1 sigma, or 8 consecutive points on one side of the center line (NIST/SEMATECH, n.d.). A sulfite log that sits below its own mean (the log's center line) for 8 shifts in a row signals a process shift, even with every point inside the control range.

The handbook also quotes Shewhart that control should not be claimed from fewer than 25 samples of size 4 (NIST/SEMATECH, n.d.), so one week of shift tests is a thin basis.

No public consensus sets a number for the in-range share, so choose one in advance, for example 90 percent of shift results within range (illustrative). Pair it with a duration rule, such as no excursion lasting longer than one shift (illustrative). An excursion corrected during a known upset counts differently from an unexplained one.

Worked boiler program review (illustrative)

The worked boiler program review below uses invented numbers for one month at a 150 psig industrial watertube boiler with a deaerator and no superheater or turbine drives. It is scored against the criteria fixed at the start of the month. All values in this section and its table are illustrative.

The month's control log holds 90 shift results each for sulfite, phosphate and neutralized conductivity. Sulfite was in range 86 times out of 90, phosphate 84, and conductivity 88, so all three meet the 90 percent rule chosen in advance. No sulfite run of 8 shifts sits on one side of center. Judged on control tests alone, the program looks well run.

The scoring table below shows how the outcome evidence changes that verdict.

Criterion

Month result (illustrative)

Threshold

Verdict

Feedwater total hardness

3 of 30 daily results at 0.8 ppm, all during one three-day softener exhaustion

Below 0.5 ppm

Fail, cause known

Feedwater total iron

0.04 to 0.06 ppm

Below 0.1 ppm

Pass

Condensate total iron

Weekly results 15, 22, 31, 44 ppb

No rising trend

Fail, cause open

Tube deposits

No outage this month

Not due

Not judged

The condensate iron row decides the review. Iron in the return system tripled over four weeks while every control test passed. That points to condensate corrosion the boiler water residuals cannot show, and the likely next checks are condensate pH, amine feed and air in-leakage at receivers. The softener event counts as a pass for the program but a fail for pretreatment, and it belongs to the pretreatment owner.

The verdict for the month: chemical control acceptable, corrosion control in the condensate system failing, with two named actions. The tube deposit line stays open. It closes at the next outage, when a tube sample from the same boiler area as the last one shows whether the iron is reaching the heat transfer surfaces.

How do you report a boiler water treatment program review?

Report a boiler water treatment program review as one verdict per criterion: the threshold and its source, the evidence that decided it, and the action and owner where it failed. Then give an overall statement that keeps chemical control separate from outcome control. The reader is usually a plant engineer or a buyer, who needs to know what the program achieved and what must change.

Put the outcome criteria first and the control test summary second, since the outcome results answer the question the review was set up to answer. For each failed criterion, say whether the cause is known and inside the program, known and outside it (pretreatment, condensate design, operations), or still open. A failure caused by a softener outage is not evidence against the treatment chemistry. Saying so prevents a supplier change that would fix nothing.

Attach the data the verdict rests on: the dated log extract, the iron trend, the inspection notes and any deposit report. If the review turns into a dispute over whether the chemical itself is at fault, apply the same evidence discipline you would use to show whether a product complaint is really about the product. In Lubinpla, the performance evaluation task fixes the judgment criteria first, judges performance status from the measurement history and leaves a PDF document for review. Keep the criteria sheet with the report so the next review starts from the same lines.

Where this boiler program review does not apply

The boiler program review described here does not apply as written to high-pressure utility boilers, heat recovery steam generators, once-through units, hot water boilers or electrode boilers. Nor does it replace a failure investigation after a tube rupture. Those cases need different limits, different monitoring or a root cause method.

Utility and combined cycle units follow their own guidance; for example, EPRI recommends below 5.0 ppb iron in all combined cycle drums to reduce iron deposition on evaporator tubes (ChemTreat, 2023). The ASME limits reproduced here cover industrial watertube boilers by pressure band. The same US Department of Defense guidance notes that in many instances these limits cannot be met for small heating boilers, such as feedwater oxygen in boilers that lack a deaerator or hardness in boilers that lack softeners (US DoD, 2026). For those boilers, build the criteria around what the plant can achieve, with chemical treatment and blowdown control carrying more of the load.

The review also breaks down when the data are not valid. If sample lines are not purged, samples are not cooled, or iron is measured as dissolved only, the outcome criteria cannot be judged. The honest verdict is then "not judged", with the data fix as the first action. Deposit weight density thresholds also differ by source and pressure, so name the source you used.

Key takeaways

  • Score a boiler program on outcomes: feedwater hardness and iron, condensate total iron, deposits and inspections.

  • Treat sulfite, phosphate, alkalinity and conductivity as evidence that the program was run, not that it worked.

  • Write thresholds, sources and actions before reviewing the period, and keep them fixed.

  • Judge control test excursions by pattern and cause; count an outcome failure as a failure.

Related posts