How to Choose an RO Antiscalant for High Silica Feed Water
Summary
Choose an RO antiscalant whose stated silica limit covers your projected reject silica, the silica calculated for the concentrate, at plant pH and temperature. Use the coldest water temperature and the reject pH for that projection, and keep feed iron and aluminum below 0.05 mg/L each (Dow FilmTec, 2009). A rating stated at another pH or temperature does not transfer.
Amorphous silica dissolves to about 100 to 140 mg/L at 25 °C, and a suggested industry guideline limits RO concentrate silica to about 120 mg/L at 25 °C (NHMRC, 2025).
The Dow FilmTec manual says silica solubility rises with temperature and increases below about pH 7.0 and above about pH 7.8 (Dow FilmTec, 2009).
Silica-specific antiscalants typically claim control only up to about 300 ppm SiO2 in the reject, according to a 2026 AMTA conference abstract (AMTA, 2026).
ASTM D4993, the practice for calculating silica scaling in RO concentrate, was withdrawn in 2023 with no replacement (ASTM, 2023).
This answer covers brackish, well and reuse water RO with dissolved silica in the feed. It does not cover seawater RO, high-pH processes run on purpose to dissolve silica, or feed water carrying colloidal silica, which needs coagulation and filtration rather than an antiscalant. The membrane maker's and antiscalant maker's own limits govern their products.
Which conditions decide an RO antiscalant for high silica feed water?
Five conditions decide the choice: projected reject silica, reject pH, minimum water temperature, iron and aluminum in the feed, and the other scalants the same product must control.
Reject silica follows from feed silica and recovery, the share of feed water that leaves as permeate. The Dow FilmTec manual gives concentrate silica as feed silica divided by (1 minus recovery) (Dow FilmTec, 2009), so 30 mg/L in the feed at 75 percent recovery gives 120 mg/L in the reject (illustrative calculation). Reject pH and temperature set how much of that silica stays dissolved, and the manual tells designers to use the minimum temperature when water temperature varies (Dow FilmTec, 2009).
Iron and aluminum decide whether silica precipitates as a metal silicate below its own saturation, and no silica rating covers that. The other scalants matter because the reject also concentrates calcium, carbonate, sulfate and phosphate, and one product has to handle all of them at once. American Water Chemicals, a membrane chemical maker, writes that the antiscalant "must be selected based on an entire water analysis" (AWC, 2013).
Before asking suppliers for products, collect a full feed analysis: silica, calcium, magnesium, iron, aluminum, alkalinity, sulfate and phosphate, plus the design recovery and the lowest and highest seasonal water temperatures.
How do pH and temperature change silica solubility in RO reject?
Silica solubility in RO reject rises with temperature and is lowest in a band near neutral pH, increasing below about pH 7.0 and above about pH 7.8 according to the Dow FilmTec manual (Dow FilmTec, 2009). At 25 °C, amorphous silica dissolves to about 100 to 140 mg/L as SiO2 (NHMRC, 2025).
The reject pH is not the feed pH. The Dow FilmTec method first calculates the concentrate pH from the feed pH and only then applies the pH correction to solubility (Dow FilmTec, 2009). Colder water holds less silica, so a plant that passes its silica check in summer can scale in winter at the same recovery.
Higher pH raises silica solubility, but the manual adds that calcium carbonate scaling must be prevented at high pH (Dow FilmTec, 2009). American Water Chemicals also notes that sodium or calcium in the water reduce the repulsion between silica ions, so silica can polymerize significantly even at high pH (AWC, 2013). Heating the feed raises the allowable recovery as well, within the manual's maximum of 45 °C for continuous use of its membrane elements (Dow FilmTec, 2009).
Run the silica solubility check for the coldest month and at the reject pH the projection predicts, not at the temperature and pH where a supplier stated its product rating.
How high can RO reject silica go with a silica antiscalant?
With a silica antiscalant, RO reject silica can go well above the untreated guideline of about 120 mg/L, but the ceiling is a supplier's claim at stated conditions, not a property of your water.
A suggested industry guideline limits concentrate silica to about 120 mg/L at 25 °C to limit membrane fouling (NHMRC, 2025). A 2026 AMTA conference abstract reports that amorphous silica fouling begins around 120 ppm SiO2 and accelerates with pH, temperature and cation concentration (AMTA, 2026). The same abstract states that silica-specific antiscalants typically claim control only up to about 300 ppm SiO2 in the reject (AMTA, 2026).
Individual product ratings sit inside that range and use different bases. Accepta rates its AT-2091 for reject brine silica as high as 230 ppm at 30 °C and pH 7.5 (Accepta, accessed 2026). American Water Chemicals rates AWC A-103 for silica up to 250 percent saturation in the reject (AWC, 2024).
Convert the product's rated value to your reject temperature and pH in the supplier's projection, then leave a margin for analysis error and seasonal swings. A rating that holds on the sheet but not in the plant is the gap described in why a product that meets its TDS specification can still fail on site. If the projection needs more than the converted rating, lower the recovery, raise the temperature or remove silica upstream instead of looking for a stronger claim.
Which high silica antiscalant fits which RO feed water?
The high silica antiscalant that fits an RO feed water depends on where projected reject silica sits against its solubility, and on what else the feed carries. Silica rating is only one column of the choice: iron, aluminum, colloids, hardness and phosphate each decide whether a silica product can work at all. The table below gives the choice or change for each feed and reject condition. Values carry their source in the cell, and the lines between rows are illustrative.
Your feed and reject conditions | What to choose or change | Why |
|---|---|---|
Reject silica below solubility at minimum temperature and reject pH | Antiscalant chosen for carbonate and sulfate; no silica product needed | No silica scaling is projected (Dow FilmTec, 2009) |
Reject silica above solubility but within a product's rating converted to your pH and temperature | Silica antiscalant or dispersant whose rating states pH and temperature | A rating applies only at its stated conditions |
Reject silica above every candidate's converted rating | Lower recovery, heat the feed (up to 45 °C for FilmTec elements), or soften to remove silica (Dow FilmTec, 2009) | No product covers the projection |
Feed Fe3+ or Al3+ at or above 0.05 mg/L, or coagulant carryover | Fix pretreatment first, then a product stated to tolerate iron and aluminum (limit: Dow FilmTec, 2009) | Metal silicates form below silica saturation |
Colloidal silica or clay in the feed | Flocculation and filtration or a prefilter of 1 µm or finer (Dow FilmTec, 2009) | Antiscalants act on dissolved silica |
High calcium or magnesium at high recovery or high pH | Product also rated for calcium carbonate, with its index limit stated | Divalent cations speed silica polymerization (AWC, 2013) |
Phosphate in the feed, as in reuse water | Product stated to inhibit calcium phosphate | Phosphate salts anchor silica on the membrane (AWC, 2013) |
The row that most often decides the choice is iron and aluminum. When either metal is at or above 0.05 mg/L in the feed, the Dow FilmTec manual expects silica to precipitate even below saturation (Dow FilmTec, 2009), so pretreatment comes before any product comparison.
Do iron and aluminum in the feed make a silica antiscalant fail?
Iron and aluminum in the feed can make a silica antiscalant fail. They form metal silicates and deactivate polymer antiscalants at concentrations far below silica saturation.
The Dow FilmTec manual names aluminum as the most powerful precipitant of silicic acid, the dissolved form of silica, and states that both Al3+ and Fe3+ "must be less than 0.05 mg/L in the feed water, even if the silica level is below saturation" (Dow FilmTec, 2009). The same manual reports that silica as low as 10 mg/L can result in aluminum silicate fouling. It also warns that antiscalants containing polymers, such as acrylic acid based products, are sensitive to iron and aluminum and can be deactivated by them (Dow FilmTec, 2009).
The ASTM silica practice notes that metals such as Al3+ may significantly alter silica solubility through insoluble metal silicates, and that it does not address this (ASTM D4993-08(2014)). American Water Chemicals adds that a silica antiscalant that cannot inhibit iron hydroxide will not be effective against silica scale in the presence of ferric ions (AWC, 2013).
Some products are sold as iron tolerant. Accepta states that AT-2091 is not deactivated in the presence of iron (Accepta, accessed 2026), which is the maker's claim. Because ferric and aluminum salts are common coagulants, the manual calls for frequent and accurate measurement of both ions even when the raw water itself is low in them (Dow FilmTec, 2009).
Why do suppliers state RO silica limits in different units and pH targets?
Suppliers state RO silica limits in different units because each rates its product on its own basis. They disagree on pH targets because published sources place the solubility minimum differently.
Three bases appear on product sheets. One is a concentration at stated conditions, such as 230 ppm at 30 °C and pH 7.5 (Accepta, accessed 2026). Another is a percent of saturation in the reject, such as 250 percent (AWC, 2024). A third is an index: the same maker's product category page rates the same AWC A-103 for silica saturation up to MSI 12 (AWC, accessed 2026), so one product carries two numbers on two bases. The sheets opened for this article do not say how their basis converts to the others. The numbers cannot be compared until each is turned into reject silica at your temperature and pH.
On pH, the Dow FilmTec manual says silica solubility increases below about pH 7.0 and above about pH 7.8 (Dow FilmTec, 2009). American Water Chemicals describes pH 8 as "the point of lowest solubility for amorphous silica" and lists running at pH 8 among misguided beliefs about silica control (AWC, 2013). Both sources agree that pH alone does not settle the limit, because dissolved cations and the calcium carbonate risk at high pH move it. Treat any fixed RO pH target for silica as a case to check in the projection, not a rule.
How do you read a supplier projection for RO silica saturation?
Read a supplier projection in a fixed order: its inputs first, then the reject silica, pH and temperature it calculates, and only then the dose it proposes. A projection is the supplier's software model of your system. American Water Chemicals, for example, says the AWC A-103 dose is typically 1 to 5 ppm depending on feed water and operating parameters and can be set with its Proton projection software (AWC, 2024).
Start with the inputs: the analysis must be recent and complete, with silica, iron, aluminum, phosphate and the full cation and anion set, because a projection without aluminum cannot show metal silicate risk. Check the temperature: the Dow FilmTec method uses the minimum water temperature when temperature varies (Dow FilmTec, 2009), so a projection run at an annual average overstates the winter margin. Check the recovery, and confirm the program reports the final reject, where silica is highest.
Then compare projected reject silica with solubility at reject pH and temperature, and read the saturation figure in the program's own unit. Ask each supplier for the same three runs: the coldest month, the maximum design recovery and the upper end of your silica results. Keep each printed projection with the feed analysis it used, so the next comparison starts from the same data.
What should you test before trusting a silica antiscalant on an RO?
Before trusting a silica antiscalant on an RO, test feed and reject silica by a stated method, confirm iron and aluminum at the RO inlet, and run a trial with normalized performance data.
Measure silica in feed and concentrate with the same method. ASTM D859-16(2021)e1, the active ASTM colorimetric method, determines molybdate-reactive silica, which includes dissolved silicates and monomeric silica but only an undetermined fraction of polymeric silica (ASTM D859-16(2021)e1), so suspected colloidal silica needs a separate check.
Once the system runs, the Dow FilmTec manual says reject silica can be calculated directly from the concentrate analysis and compared with the projection (Dow FilmTec, 2009). Normalize permeate flow and salt passage to constant conditions as ASTM D4516-19a describes, so a winter temperature drop is neither mistaken for scaling nor allowed to hide it (ASTM D4516-19a). Watch the last stage, where reject silica is highest, and raise recovery in steps only after each step holds. Fix the pass criteria before the trial starts, such as the allowed drop in normalized permeate flow over a set number of weeks (illustrative).
Lubinpla treats this as a product recommendation case: it reads the project's water analysis history first to fix the requirements, compares candidate antiscalants with a source on every data value, and passes what remains open to trial checks.
Frequently asked questions
Can an RO run on high silica feed water without a silica antiscalant?
Yes, if projected reject silica stays below silica solubility at the minimum water temperature and the reject pH. The Dow FilmTec manual says a lower recovery must be used when concentrate silica exceeds the corrected solubility (Dow FilmTec, 2009). The cost is less permeate per unit of feed water.
Can softening remove silica before the RO?
Yes. The Dow FilmTec manual describes lime and soda ash softening with sodium aluminate and ferric chloride to lower feed silica, and a hot lime process at 60 to 70 °C with lime and porous magnesium oxide that can reduce silica to 1 mg/L (Dow FilmTec, 2009). The manual adds that softening must be run properly to prevent insoluble metal silicates forming in the RO (Dow FilmTec, 2009).
Should a silica antiscalant be diluted before dosing?
Only as its maker allows. American Water Chemicals designs AWC A-103 to be fed neat and dilutes it only when the pump's minimum output exceeds the dose (AWC, 2024). Accepta allows AT-2091 to be diluted with RO permeate only (Accepta, accessed 2026). Follow each product's SDS and sheet.