KPIs to agree in a water treatment service contract
Summary
Choose outcome KPIs, such as control-range compliance and corrosion rate, when the supplier controls dosing; choose visit and reporting KPIs when the plant does. Most cooling and process water contracts need both kinds. Agree each outcome target for the specific system and water, because published targets assume typical systems and typical waters.
UK guidance gives a typical desired outcome for carbon steel corrosion in cooling water of generally less than 5 mpy and preferably less than 2 mpy, for typical systems and typical waters (HSE, 2024).
UK guidance gives typical desired outcomes of not more than 1×10^4 cfu/ml general microbial activity and Legionella not detected or not more than 100 cfu/l in cooling water (HSE, 2024).
UK guidance recommends weekly dip slides and Legionella sampling at least quarterly for evaporative cooling systems (HSE, 2024).
ASTM D2688-23, the active edition, determines corrosion rate in a water system without heat transfer from coupon weight loss and pitting (ASTM International, 2023).
This guide covers chemical treatment service contracts for open recirculating cooling systems and closed loops at industrial sites. Boiler water limits, municipal operation contracts and the legal duties for Legionella control in your jurisdiction are outside it. The numeric targets quoted come from UK guidance and are examples to adapt, not limits for every system.
Which conditions decide the KPIs in a water treatment service contract?
The KPIs in a water treatment service contract depend on who controls the levers that move each result: chemical dosing, bleed-off, cleaning and the plant's operating conditions. A supplier can be held to a result only when it controls the inputs that produce that result.
Three conditions decide the KPI set. The first is control of dosing and bleed. If the supplier owns the controller, sets the setpoints and fills the tanks, control-range compliance and corrosion rate can be its KPIs. If plant operators adjust dosing pumps or bleed valves, those results are shared, and the supplier's KPIs move to testing, advice and reporting.
The second is measurement. A KPI needs an agreed method, sampling point and frequency before the contract starts; otherwise the review turns into an argument about data.
The third is the system's condition at the start. A system with existing deposits, corrosion or a history of high counts needs a baseline survey, so that later results are compared with the starting state.
UK guidance places that agreement squarely with the two parties: "The particular desired outcomes and the metrics to be used should be agreed between the system owner/operator and their specialist water treatment service provider" (HSE, 2024). For each KPI, write down who measures it, how, how often and what counts as a pass.
Which water treatment KPIs measure results rather than activity?
Water treatment KPIs that measure results are control-range compliance, corrosion rate, scale and deposit condition, and microbial and Legionella results. Visit completion and report delivery measure activity. Result KPIs show whether the system is protected, while activity KPIs show whether the supplier did the agreed work.
For a supplier that runs the dosing, control-range compliance is the most practical result KPI. For each controlled parameter, count the readings taken in the period and report the share that fell inside the agreed range. A figure such as 46 of 52 conductivity readings in range (illustrative) tells the plant more than "system under control".
Corrosion, deposit and microbial results come more slowly and need a lab or a shutdown, so they suit quarterly or annual review rather than every visit.
Use the table below to decide which KPI belongs in the contract, given who controls dosing and who takes the measurement.
KPI | Fits when | Who measures | Watch out |
|---|---|---|---|
Control-range compliance: share of readings within the agreed range for conductivity, pH, inhibitor and biocide | Supplier controls dosing and setpoints | Supplier on each visit; site staff between visits | Agree the ranges and the reading count before the contract starts |
Corrosion rate on coupons, carbon steel generally below 5 mpy and preferably below 2 mpy for typical systems (HSE, 2024) | Supplier controls the inhibitor program and the system has a coupon rack | Supplier installs and sends coupons to a lab; method per ASTM D2688-23 | Process cooling may need a different target (HSE, 2024) |
Scale and deposit condition, calcium balance above 0.9 as a typical outcome (HSE, 2024) | Supplier controls scale inhibitor and cycles | Joint inspection at planned shutdowns | Inspections depend on plant access |
Microbial activity not above 1×10^4 cfu/ml and Legionella not detected or not above 100 cfu/l (HSE, 2024) | Supplier controls the biocide program | Site staff or supplier for dip slides; accredited lab for Legionella | The dutyholder keeps the legal duty |
Visit completion and report delivery | Plant controls dosing or bleed | Supplier, checked against the visit plan | Counts work done, not protection |
The corrosion row carries the most weight. A coupon is a metal specimen exposed in the system and then checked for weight loss and pitting. A coupon result below the agreed target, with no pitting, is the clearest single sign that the treatment program protects the metal.
How do corrosion coupon and scale readings work as contract KPIs?
Corrosion coupon and scale readings work as contract KPIs when the contract fixes the coupon metal, rack position, exposure period, lab method and target before the first coupon goes in. Without those, two coupon results cannot be compared.
ASTM D2688-23, the active edition, covers the determination of the corrosion rate in a water system in the absence of heat transfer by measuring the weight loss of metal coupons and evaluating pitting, using a side stream corrosion specimen rack (ASTM International, 2023). The standard states that corrosion rate is determined in relative, rather than absolute, terms, so the KPI works best as a comparison: with the agreed target and with earlier coupons from the same rack. Report pitting with the weight loss result, because a low average rate can hide localized attack.
UK guidance gives corrosion rate examples for typical cooling systems with typical waters: carbon steel generally below 5 mpy and preferably below 2 mpy, where 1.0 mpy equals 0.0254 mm/a (HSE, 2024). The same guidance notes that coupon analysis is not typically included for smaller cooling systems unless it is a contractual requirement, so write it in if you want it.
Total iron below 1.0 mg/l is a typical control limit, but a level below 1.0 mg/l does not definitively indicate good corrosion control (HSE, 2024).
For scale, pair a calculated indicator such as calcium balance with a visual inspection of pack, distribution and heat exchanger surfaces at planned shutdowns.
Who is responsible for measuring each water treatment KPI?
Each water treatment KPI needs one named party responsible for measuring it, written into the contract next to the method and frequency. In practice the split follows who is on site. Plant staff take routine readings between visits, the supplier tests on each visit, and a laboratory handles coupons and Legionella samples.
UK guidance says the typical on-site monitoring and analytical checks for cooling water "can be carried out by competent site personnel or by a water treatment company" (HSE, 2024). The contract should say which. One common split, illustrative only: site staff record daily visual checks, weekly dip slides and conductivity; the supplier tests pH, inhibitor, biocide residual, hardness and chloride on each visit and checks controller calibration; an accredited laboratory analyzes Legionella samples and coupons.
The legal duty does not move with the contract. In UK guidance, contractors have legal responsibilities, but the ultimate responsibility for the safe operation of the cooling system rests with the dutyholder (HSE, 2024), and the UK Approved Code of Practice L8 gives ACOP status to the role of the appointed responsible person (HSE, 2013).
In the United States, ANSI/ASHRAE Standard 188-2021 establishes minimum legionellosis risk management requirements for building water systems, and its 2021 edition replaced permissive language with enforceable language to support adoption in codes (ASHRAE, 2021). Where the site's water management program sets control limits, take the Legionella and microbial KPIs from that program rather than writing new ones.
How often should water treatment visits and reports happen under the contract?
Water treatment visits and reports under a contract should follow the monitoring frequencies the system needs. UK guidance gives these as weekly for conductivity, pH, oxidizing biocide and microbial activity and monthly for most other analyses, with a monthly water treatment report. The visit schedule then follows from who takes each reading.
UK guidance gives typical cooling water analysis frequencies of weekly for conductivity, pH, oxidizing biocide and microbial activity, and monthly for hardness, alkalinity, inhibitor level, total iron, chloride, concentration factor and calcium balance (HSE, 2024). It recommends weekly dip slides and Legionella sampling on at least a quarterly basis (HSE, 2024). The same guidance refers to monthly water treatment reports, which the responsible person and the provider should review jointly to agree actions (HSE, 2024).
Inspection frequency depends on fouling risk. UK guidance gives typical, non-prescriptive inspection intervals of at least every three months for a cooling system in a dirty environment, at least twice a year for comfort cooling, and at least every 12 months for a clean industrial application (HSE, 2024).
From this schedule, write two activity KPIs: planned visits completed in the month, and each service report delivered within an agreed number of working days after the visit (illustrative). They belong in every contract, including one with outcome KPIs, because they show whether the measurements behind the outcome KPIs exist.
How do you report water treatment KPIs at a contract review?
Report water treatment KPIs at a contract review by showing each agreed KPI against its target for the period, with the readings behind it, the excursions (readings outside the agreed range), the actions taken and the open risks. A review built only from visit counts tells the plant what the supplier did, not whether the system stayed protected.
Organize the review report by KPI, in the order of the contract. For each one, give the target, the result for the period, the number of readings or coupons behind the result, and each excursion with its cause and corrective action. Keep a separate list of risks still open, such as a coupon rack out of service or a missed Legionella sample, and of changes proposed for the next period. Monthly review of KPIs with the main stakeholders is the pattern Veolia describes for its integrated services contract at Tomago Aluminium (Veolia, n.d.).
Keep the records long enough to support the review. UK guidance says monitoring and inspection records should be kept for at least five years (HSE, 2024).
Turning the period's results into a case for renewal is covered in showing the value of technical service before a contract renewal. In Lubinpla, the account technical support status task organizes the period's work logs and project records under each agreed contract item into a review report, which you check before it goes to the customer.
Frequently asked questions
Should water treatment KPIs be tied to payment?
Tie payment only to KPIs the supplier fully controls and measures by an agreed method, such as visit completion, report delivery and, where it controls dosing, control-range compliance. Large operation contracts do link pay to KPIs: the SUEZ contract with Nama Water Services in Oman links the operator's remuneration to 33 KPIs (Oman Observer, 2026).
What if the system already had corrosion or deposits before the contract?
Run a baseline before the contract starts: install coupons, inspect accessible surfaces, record water analysis and note existing deposits with photographs. Set outcome targets against that baseline for the first period, and agree when the standard targets apply, so the new supplier is not judged on damage it did not cause.
Do boiler water treatment contracts use the same KPIs?
Boiler contracts use the same structure of outcome and activity KPIs, but the measured parameters and limits differ. Boiler water limits depend on operating pressure, boiler type and the manufacturer's requirements, so take boiler targets from the boiler maker's water quality requirements, not from cooling water guidance.